Post on 10-Oct-2015
Curso Bsico de Construccin de un motor BediniNoviembre 2013
Por Arturo Cano Jaraba
A QU LLAMAMOS MOTOR BEDINI
Introduccin
John Bedini 1984
SSG Esquema de John Bedini
SSG motor (Simplified School Girl motor)
SG motor (school girl motor)
ES OVERUNITY ESTE MOTOR?
Motor BEDINI
es overunity este motor?
No, nunca vas a obtener del motor ms energa de la que pongas. Da igual cmo lo midas.
TUV test
John Bedini dice que puedes cargar cuatro bateras al precio de una!
TUV testBATTERY TEST FOR THE BEDINI MOTOR GENERATOR
DATE : OCTOBER 13, 2000 BATTERY TEST SEQUENCE:One lead acid gel-cell (12 volts, 450 milliamps) is being utilized as the primary source fully charged at 12.5 volts. Three (3) lead acid gel-cell batteries (12 volt, 450 milliamps) strapped in parallel are being used as the charge destination. The batteries are discharged to 10 volts for the test purposes. Test #1 starts at 10:45 AM utilizing primary battery fully charged at 12.5 volts charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 14 volts at 11:20 AM. The destination batteries are then discharged to 10 volts under working load to prepare for Test #2. Test #2 starts at 11:25 AM utilizing primary battery measured at 11.5 volts. Charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 14 volts at 12:50 PM. The destination batteries are then discharged to 10 volts under working load to prepare for Test #3. Test #3 starts at 1:00 PM utilizing primary battery measured at 10.5 volts. Charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 14 volts at 1:40 PM. The destination batteries are then discharged to 10 volts under working load to prepare for Test #4. Test #4 starts at 2:05 PM utilizing primary battery measured at 9.5 volts. Charging three (3) destination batteries paralleled. The destination batteries reach a charge capacity of 13 volts at 2:40 PM. The primary battery is now discharged to 9 volts under working load and unable to further run the Bedini motor generator. TOTAL BATTERIES CHARGED: 12 lead acid gel-cell batteries (12 volts, 450 milliamps each). This ratio is a 12 to 1 charging factor. The motor operation (work) being performed as this was done is not included as an additional factor in this test.
es overunity este motor?
Pero no dices que no es OVERUNITY?
Qu ms hace un motor Bedini?
Se mueve, hace un trabajo y puedes aprovecharlo, por ejemplo te puedes hacer un ventilador .
Carga bateras sin calentarlas Carga bateras ms rpido que un cargador
convencional Recupera bateras sulfatadas Genera energa radiante
MATERIAL NECESARIO
MOTOR BEDINI
Material necesario
Rueda de bicicleta o un rotor. NO MAGNTICA. Usa tu imaginacin
Material necesario
Un carrete de plstico u otro material no magntico.Plastico, 75mm largo, 18mm
dametro del agujero central
Material necesario
Varillas de soldadura.Lincoln R60.
Acero recubiertas de cobre 1,6 mm.
Material necesario
Imanes Cermicos Aconsejables (25mm x 50mm x 18mm).OJO! NO DE NEODIMIO
Material necesario
Soporte para el rotorAconsejable de madera o plstico- NO MAGNTICO!
Material necesario
Hilo de Cobre45 metros
0,4mm y 0,56 mm
Material necesario
Bateras de plomoAconsejables de ciclo profundo. Para este motor como mnimo de 7 Amp. No fuerces la batera por encima del C20
Transistor
2N3055, 100V, TO-3 MJL21194
Hilo de conexin
2 Diodos
1N4001, 1A, 50V (1N914)
1N4007, 1A, 1000V ( 1N5408)
Lmpara de Nen Resistencia
100 ohms, w
Potencimetro
1K ohms, 2 w
Herramientas que puedes necesitar
Tijeras o pela cables Ampermetro de 5 amp (como muy poco de
1 amp) Polmetro Alicates para cortar las varillas Soldador y estao Destornilladores Cuenta km de bici o un tacmetro Brjula Cinta aislante Pegamento Loctite o Glue 3 Cinta americana
Y DESPUS DE CONSTRUIDO QU
MOTOR BEDINI
Pruebas
Calculadora de COP
HAGAMOS UN MOTOR
MOTOR BEDINI
La seguridad es lo primero
Los imanes si salen disparados son peligrosos. Usa cinta americana o equivalente alrededor de la rueda para sujetar los imanes. Esta seguridad es adicional a pegar los imanes a la rueda.
Las bateras de plomo contienen cido sulfrico que es altamente corrosivo y es venenoso. Cuando se trabaja con bateras debes usar gafas de seguridad y ropa de proteccin adecuada, el espacio de trabajo debe estar ventilado y debes quitarte todo tipo de joyas, relojes, etc.
Lava tus manos despus de estar en contacto con las bateras. Para neutralizar cido derramado usa bicarbonato de sosa.
SSG motor (Simplified School Girl motor)
SG motor (Pulser)