Post on 03-Nov-2015
description
SOBREANCHO DE LA CALZADA EN CURVAS CIRCULARES PARA UN CARRIL
VELOCIDADRADIO DE CURVA (m)
KM/H15203040506080100125150200300400500
203.22.501.501.201.000.800.600.500.400.400.300.200.200.20
30*2.501.701.301.000.900.700.600.500.400.300.200.200.20
PERALTE DE LA CALZADA EN CURVAS CIRCULARES PARA UN CARRIL
RADIO DE CURVA (m)
162030506080100125150
6%6%5%5%4%4%3%3%3%
BasicLaneSHARELIKE (0)This subassembly creates a simple lane.This subassembly is one of a group of Getting Started subassemblies used for simple roadway modeling, and for tutorial and training purposes.
AttachmentThe attachment point is at the inside edge of lane on finish grade.Input ParametersNote: All dimensions are in meters or feet unless otherwise noted. All slopes are in run-over-rise form (for example, 4 : 1) unless indicated as a percent slope with a % sign.ParameterDescriptionTypeDefault
SideSpecifies which side to place the subassemblyLeft / RightRight
WidthWidth of the laneNumeric, positive3.6 m12.0 ft
DepthDepth from finish grade to subbaseNumeric, positive0.2 m0.67 ft
%Slope% Slope of the laneNumeric-2%
Target ParametersThis section lists the parameters in this subassembly that can be mapped to one or more target objects. For more information, see in theAutoCAD Civil 3DUsers Guide Help.Target Parameters: None.Output ParametersParameterDescriptionType
SideSpecifies which side to place the subassemblyLeft / Right
WidthWidth of the laneNumeric, positive
DepthDepth from finish grade to subbaseNumeric, positive
%Slope% Slope of the laneNumeric
BehaviorThe subassembly builds a finish grade and subbase surface, closed by vertical links at either end. The lane is inserted outward from the attachment point for the given width, depth, and slope.Layout Mode OperationIn layout mode, this subassembly draws the lane using the input parameters.Point, Link, and Shape CodesThe following table lists the point, link, and shape codes for this subassembly that have codes assigned to them. Point, link, or shape codes for this subassembly that do not have codes assigned are not included in this table.Point, Link, or ShapeCodesDescription
P1CrownCrown of road on finish grade
P2ETWEdge-of-traveled-way on finish grade
P3Crown_SubbaseCrown of road on subbase
P4ETW_SubbaseEdge-of-traveled-way on subbase
L1Top, PavePaved finish grade
L3Datum, SubbaseSubbase
S1Pave1
Coding Diagram
Parent topic:Subassembly ReferenceWas this Article Helpful?Please help us improve the content on this site. Was this article helpful?YesNo
ShoulderExtendAllSHARELIKE (1)This subassembly inserts a paved shoulder with all pavement, base, and subbase layers extended to the shoulder daylight slope.
AttachmentThe attachment point is at the inside edge of the paved shoulder, which is typically at the outside edge-of-traveled way.Input ParametersNote: All dimensions are in meters or feet unless otherwise noted. All slopes are in run-over-rise form (for example, 4 : 1) unless indicated as a percent slope with a % sign.ParameterDescriptionTypeDefault
Daylight ElevationNumeric- 1.667
Daylight OffsetNumeric8.377
Daylight SlopeThe value of the fixed slope of the daylight link, used if the hold slope option is used.Numeric, positive4 ( : 1)
SideSpecifes to insert the subassembly either on the right or the left side of the attachment point.Left/RightRight %
Shoulder WidthThe value of the fixed width of the daylight link, used if the hold width option is used.Numeric, positive8.000 ft
Use Superelevation SlopeSpecifies to use the slope from the superelevation specification defined on the baseline alignment.Selection List: No Left Outside Shoulder Left Inside Shoulder Right Inside Shoulder Right Outside ShoulderNo
Shoulder Slope DirectionSpecifies whether the shoulder slopes away from the crown or towards the crownSelection List: Away from Crown Towards CrownAway from Crown
Shoulder % SlopeDefault cross slope of the shape surface. This value is used if superelevation slope is not used, or is not specified for the baseline alignment.Numeric- 2.0 %
Subbase Daylight TypeSelect whether to hold the daylight link to a fixed slope with variable width, or hold it to a fixed width with variable slopeSelection list: a) Hold Slope, Adjust Width, b) Hold Width, Adjust SlopeHold Slope, Adjust Width
Daylight SlopeThe value of the fixed slope of the daylight link, used if the hold slope option is used.Numeric, positive4 ( : 1)
Daylight WidthThe value of the fixed width of the daylight link, used if the hold width option is used.Numeric, positive5.40 ft1.8 m
Superelevate SubbaseSpecifies to use shoulder superelevation slope to subbaseNo
Subbase % SlopeDefault cross slope of the shape surface. This value is used if superelevation slope is not used or is not specified for the baseline alignmentNumeric- 2.0 %
Pave 1 DepthThickness of the Pave1 layer (zero to omit)Numeric, non-negative0.083 ft
Pave 2 DepthThickness of the Pave2 layer (zero to omit)Numeric, non-negative0.083 ft
Base DepthThickness of the Base layer (zero to omit)Numeric, non-negative0.0333 ft
Subbase DepthThickness of the Subbase layer (zero to omit)Numeric, non-negative1.000 ft
Target ParametersThis section lists the parameters in this subassembly that can be mapped to one or more target objects, such as a surface, alignment, or profile object in a drawing. For more information, see in theAutoCAD Civil 3DUsers Guide Help.ParameterType of AssignmentStatus
Shoulder WidthMay be used to override the fixed Shoulder Width and tie the edge-of-shoulder to an offset alignment. The following object types can be used as targets for specifying this offset: alignments, polylines, features lines, or survey figures.Optional
Output ParametersParameterDescriptionType
Daylight SlopeSlope of the daylight linkNumeric
Daylight OffsetOffset of the subgrade daylight pointNumeric
Daylight ElevationElevation of the subgrade daylight pointNumeric
Shoulder WidthWidth of the paved shoulderNumeric
Shoulder SlopeSlope of the paved shoulderNumeric
BehaviorThe finish grade of the shoulder is inserted for the given Shoulder Width and Default Shoulder Slope outward from the attachment point. The subbase link is inserted from the attachment point starting at the Subbase Depth below the finish grade.The shoulder daylight link can be inserted with either a fixed slope (Hold Daylight Slope = True), or a fixed width (Hold Daylight Slope = False). If a fixed slope is used, the daylight link is extended from the outside edge of the shoulder until it intersects the subbase link. Otherwise, the subbase layer is extended for the Daylight Width beyond the outside edge of the shoulder, and the daylight link is connected to the end of the subbase.The Pave1, Pave2, and Base surface links are inserted parallel to the finish grade at the given depths until they intersect with the shoulder daylight link.Layout Mode OperationIn layout mode, this subassembly displays the links comprising the shoulder for a normal crown roadway situation, using default shoulder and subbase cross slope.Point, Link, and Shape CodesThe following table lists the point, link, and shape codes for this subassembly that have codes assigned to them. Point, link, or shape codes for this subassembly that do not have codes assigned are not included in this table.TypeCodeDescription
P2EPSEdge of paved shoulder, finish grade
P4EPS_Pave1Edge of paved shoulder on Pave1
P6EPS_Pave2Edge of paved shoulder on Pave2
P8EPS_BaseEdge of paved shoulder on Base
P10Daylight_SubSubbase daylight point
L1Top, PavePaved finish grade
L3PavePaved finish grade
L4Pave1Top of Pavement2
L6Pave1Top of Pavement2
L7Pave2Top of Pavement3
L9Pave2Top of Pavement3
L10BaseTop of the base course
L12BaseTop of the base course
L13Subbase, DatumBottom of subbase, datum
L14Slope_LinkTop surface formation. L14 is the link connecting P2-P10 or P2-P8 or P2-P6 or P2-P4, depending on which is the lowest link
S1Pave1
S2Pave2
S3Base
S4Subbase
Note:L14 is the new link connecting P2-P10 or P2-P8 or P2-P6 or P2-P4, depending on which is the lowest link.Coding Diagram
Parent topic:Subassembly Reference (continued)Was this Article Helpful?Please help us improve the content on this site. Was this article helpful?YesNo
endienteTaludCunetaDesmonteBsicaCOMPARTIRME GUSTA (0)Este subensamblaje se utiliza para cerrar desde el borde de la carretera hasta un vrtice, tanto en condiciones de desmonte como de terrapln.En condiciones de desmonte incluye una cuneta opcional. En los casos en que el modelo de obra lineal deba dejarse en un estado incompleto, se puede omitir el vnculo de interseccin final. Por ejemplo, para que las superficies de explanacin de propiedades adyacentes se puedan asociar al punto de articulacin sobre la carretera sin completar. ste es uno de los subensamblajes de un grupo de subensamblajes iniciales que se utilizan para el modelado simple de carreteras, as como para los aprendizajes y la formacin.Tambin es posible especificar materiales revestidos opcionales para la interseccin y otros vnculos (Todos los vnculos, Vnculos de interseccin, Slo vnculos de terrapln y Ninguno).
EnlaceEl punto de enlace se encuentra en el borde interior del talud interior de cuneta en caso de desmonte, y en el borde interior del vnculo de interseccin en caso de terrapln.Parmetros de entradaNota: todas las dimensiones se ofrecen en metros o en pies a menos que se indique lo contrario. Todos los taludes se expresan como recorrido por altura (por ejemplo, 4:1), a menos que se indiquen como un porcentaje de talud mediante el signo %.ParmetroDescripcinTipoValor por defecto
LadoPrecisa en qu lado se coloca el subensamblajeIzquierda / DerechaDerecha
Vnculo de interseccinPermite incluir u omitir el vnculo de interseccin.Incluir / OmitirIncluir
Talud en desmonteTalud del vnculo de interseccin para desmonteNumrico, positivo2:1
Talud en terraplnTalud del vnculo de interseccin para terraplnNumrico, positivo4:1
Talud interior de cunetaTalud del vnculo de talud interior de cuneta (slo para desmonte)Numrico, positivo4:1
Anchura de talud interior de cunetaAnchura del vnculo de talud interior de cuneta (slo para desmonte)Numrico, positivo1.2 m4.0 pies
Anchura inferiorAnchura de la parte inferior de la cunetaNumrico, positivo0.6 m2.0 pies
Talud exterior de cunetaTalud del vnculo de talud exterior de cuneta (slo para desmonte)Numrico, positivo4:1
Anchura de talud exterior de cunetaAnchura del vnculo de talud exterior de cuneta (slo para desmonte)Numrico, positivo1.2 m4.0 pies
Opcin de redondeoPrecisa redondear el vnculo de interseccin en el punto de recepcinCadenaNinguno
Redondear porPrecisa el parmetro que debe utilizarse para el redondeoCadenaLongitud
Parmetro de redondeoPrecisa el valor de la longitud del radioNumrico, positivo1.500 pies
Triangulacin de redondeoPrecisa el nmero de puntos intermitentes en los vnculos de redondeo (10 vnculos como mximo)Numrico, positivo6
Colocar material revestidoPermite especificar la colocacin de material opcional de revestimiento en los vnculos de interseccin. Puede seleccionar entre Todos los vnculos, Vnculos de interseccin, Slo vnculos de terrapln y Ninguno.CadenaNinguno
Lmite 1 del taludPermite especificar el lmite de talud hasta el que se colocar el material de revestimiento asociado.Talud1 : 1
Grosor del material 1Permite especificar el grosor del material revestido.Numrico, positivo12 pulgadas
Nombre del material 1Permite especificar el nombre del material que se aplica al revestimiento a lo largo de los vnculos de explanacin.CadenaRevestimiento del talud
Lmite 2 del talud 2Permite especificar el lmite de talud hasta el que se colocar el material de revestimiento asociado.Talud2:1
Grosor del material 2Permite especificar el grosor del material revestido.Numrico, positivo6 pulgadas
Nombre del material 2Permite especificar el nombre del material que se aplica al revestimiento a lo largo de los vnculos de explanacin.CadenaRevestimiento del talud
Lmite 3 del talud 3Permite especificar el lmite de talud hasta el que se colocar el material de revestimiento asociado.Talud4:1
Grosor del material 3Permite especificar el grosor del material revestido.Numrico, positivo4 pulgadas
Nombre del material 3Permite especificar el nombre del material que se aplica al revestimiento a lo largo de los vnculos de explanacin.CadenaCsped
Parmetros de objetivoEsta seccin muestra los parmetros de este subensamblaje que se pueden asignar a uno o a varios objetos de destino. Para obtener ms informacin, consulte en la Ayuda del Manual del usuario deAutoCAD Civil 3D.ParmetroDescripcinEstado
Superficie de interseccinNombre de la superficie para la interseccin. Los tipos de objeto siguientes se pueden utilizar como destinos para especificar la superficie: superficies.Obligatorio
Parmetros de salidaNinguno.ComportamientoEl punto de enlace se comprueba para determinar si est en desmonte o terrapln. Si est en terrapln, el vnculo de interseccin en terrapln se extiende hasta la superficie de interseccin con el talud en terrapln indicado. En caso de desmonte, se aaden el talud interior, el exterior y la parte inferior de la cuneta, mientras que el vnculo de interseccin en desmonte se extiende desde el extremo del talud exterior de cuneta hasta la superficie de interseccin con el talud en desmonte indicado.De manera opcional, este subensamblaje permite aadir un material revestido. Es posible especificar tres intervalos de talud. El tipo de material 1 se aplica si el talud de los vnculos alcanza el valor de talud especificado. El segundo tipo de material se aplica desde el talud 1 hasta el talud 2. Del mismo modo, si los taludes de los vnculos se encuentran entre los valores de los taludes 2 y 3, se aplica el material 3. Si los taludes del vnculo son ms planos que el lmite 3 del talud, no se aplica ningn material.Si se aade un material revestido al subensamblaje, los vnculos paralelos se aaden a los vnculos de interseccin con el grosor especificado. Los vnculos de nivel inferior se codifican con el valor de Cota de referencia y los vnculos de interseccin, con el valor de Superior. Las formas que encierran estos materiales se codifican con el nombre del material.Operacin en modo de diseoEn modo de diseo, este subensamblaje dibuja un talud genrico en desmonte y terrapln con flechas en los extremos.Cdigos de punto, vnculo y formaEn la siguiente tabla se muestran los cdigos de punto, de vnculo y de forma de este subensamblaje que tienen cdigos asignados. Los cdigos de punto, de vnculo y de forma de este subensamblaje que no tienen cdigos asignados no se incluyen en esta tabla.Punto, vnculo o formaCdigosDescripcin
P1HingeHinge_FillSlo en condicin de terrapln: punto de articulacin para el vnculo de interseccin en terrapln
P2Ditch_InDaylightDaylight_FillSlo en condicin de desmonte: borde interior de la cunetaSlo en condicin de terrapln: vrtice
P3Ditch_OutSlo en condicin de desmonte: borde exterior de la cuneta
P4Hinge_CutSlo en condicin de desmonte: punto de articulacin para el vnculo de interseccin en desmonte
P5DaylightDaylight_CutSlo en condicin de desmonte: vrtice
L1 - L4TopDatumRasante sin pavimentar
L1TopDatumDaylightDaylight_FillVnculo de interseccin en terrapln
L4TopDatumDaylightDaylight_CutVnculo de interseccin en desmonte
Diagrama de codificacin
Tema principal:Referencia de subensamblajeLe ha resultado de ayuda este artculo?Aydenos a mejorar el contenido de este sitio. Le ha resultado de ayud