Bsp Rosca Cuerda
-
Upload
luis-acevedo -
Category
Documents
-
view
235 -
download
0
Transcript of Bsp Rosca Cuerda
-
7/25/2019 Bsp Rosca Cuerda
1/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
2.54
Rosca BSP conforme DIN/ISO 228
BSP to ISO 228 to DIN/ISO 228
Signo /Abbreviation: GDesignacin /Description: ISO 228-G 1/2" ISO 228-G 1/2" A
Tipo de rosca /Type: Rosca interior cilndrica Rosca exterior cilndrica(Tol. clase A)
parallel inside parallel outside(Tol. class A)
Aplicacin /Uses: Rosca de tubo, para racores sin estanqueidad en la rosca
Pipe fittings, not sealing on the thread
Altura de rosca h = 0.640327*PAltura del triangulo de perfil H = 0.960491*PRedondeamiento interior y exterior r = 0.137329*P
Altura de rosca P
angulo de engrane 55
ex
terior
engrane
interior
h H
H/6
i
H/6
Descripcin:Esta rosca sirve principalmente para la unin mecnica de piezas de racorera y robinetera. La estanqueidad se consigue mediante la
presin de dos superficies estancas fuera de la rosca y por medio de la colocacin en el medio de una junta apropiada. Los empalmes
roscados de forma A (con anillo obturador), de forma B (con canto obturador) y de forma E (previo acuerdo), as como los correspon-
dientes alojamientos roscados de forma X (con salida de rosca) y forma Y (con ranura) conforme a DIN 3852, parte 2 respectivamente,
tienen rosca G segn esta norma.
Description:
This thread is mainly used for mechanical connection of fittings. The seal results from the pressing together of two sealing faces outside
the thread and from the use of a proprietary sealing material. Male studs (with sealing ring), Form B (with sealing edge) and Form E
(on agreement) as well as the respective Form X tapped holes (with run out) and Form Y (with grooves), to DIN 3852 Part 2 have G
threads to this standard.
mximo exterior minimo interior Rosca N de vueltas para rosca exterior engrane para rosca interior
Thread No of threads P h max. outside for OT Haunch min. core for ITG i
G 1/8" 28 0,907 0,581 9,728 9,147 8,566 8
G 1/4" 19 1,337 0,856 13,157 12,301 11,445 12
G 3/8" 19 1,337 0,856 16,662 15,806 14,950 12
G 1/2" 14 1,814 1,162 20,955 19,793 18,631 14
G 5/8" 14 1,814 1,162 22,911 21,749 20,587
G 3/4" 14 1,814 1,162 26,441 25,279 24,117 16
G 1" 11 2,309 1,479 33,249 31,770 30,291 18
G 1 1/8" 11 2,309 1,479 37,897 36,418 34,939
G 1 1/4" 11 2,309 1,479 41,910 40,431 38,952 20
G 1 1/2" 11 2,309 1,479 47,803 46,324 44,845 22G 1 3/4" 11 2,309 1,479 53,746 52,267 50,788
G 2" 11 2,309 1,479 59,614 58,135 56,656 24
-
7/25/2019 Bsp Rosca Cuerda
2/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
Rosca BSP conforme DIN 2999
BSP to DIN 2999
Signo /Abbreviation: Rp RDesignacin /Description: DIN 2999-Rp-1/2 DIN 2999-R-1/2-1 ISO 7/1
Tipo de rosca /Type: Rosca interior cilndrica Rosca exterior cnica (Cono 1:16)
Parallel inside Tapered outside (taper 1:16)
Aplicacin /Uses: Rosca de tubo, para tubos roscados y racores, con estanqueidad en la rosca mediante
agente obturador.Pipe fittings, for threaded pipe and fittings, sealing in the thread with
sealing material.
Altura de rosca h = 0.640327*PAltura del triangulo de perfil H = 0.960491*PRedondeamiento interior y exterior r = 0.137327*P
Paso de Rosca P
ngulo de engrane 55
exterior
engrane
interior
h
H H/6
ex
terior
engrane
exteriortubo
Longitud de rosca utilizable iPlano de referencia a
1,7
9
1,7
9
Situacin del perfil perpendicular al ejeAngu lo de e ngrane 55
Descripcin:La rosca exterior cnica R tiene en el plano de referencia a el mismo dimetro exterior, interior y de engrane que la rosca interior cilndri-ca Rp, de modo que se puede enroscar manualmente hasta el plano de referencia a. El apriete fuerte por medio de una herramientaaumenta la longitud de penetracin y confiere estanqueidad al racor con la ayuda de un agente obturador adecuado (como camo ocinta de tefln).Comparacin con la norma DIN/ISO 228: La rosca interior cilndrica Rp de esta norma tiene las mismas medidasnominales para los dimetros de rosca y el mismo perfil de rosca que la rosca interior cilndrica G conforme a DIN/ISO 228. La roscainterior G solamente tiene tolerancias positivas en el dimetro de engrane e interior, mientras que la rosca interior Rp tiene tolerancias conforme a DIN 2999. Por este motivo, se puede enroscar una rosca exterior cnica R (DIN 2999) en una rosca interior cilndrica G(ISO 228). No obstante, se puede seguir enroscando la rosca exterior aprox. 1 vuelta, originndose en la rosca G un espacio libremayor entre las crestas de rosca y, por lo tanto, un camino de fuga mayor a causa de la gran tolerancia del dimetro interior.En ningn caso combinar la rosca exterior cilndrica G (ISO 228) y la rosca interior cilndrica Rp (DIN 2999), ya que la rosca interiorpuede ser demasiado estrecha.
Description:
The tapered R outside thread has the same core, haunch and outside dia as the Rp inside thread, so that it can be threaded in by hand.The torque from the spanner lengthens the tapped hole and seals with the aid of a proprietary sealing material (eg. PTFE tape).Comparison with ISO 228: The parallel Rp inside thread of this Standard has the same nominal size for the thread dia and profile asfor the inside thread to ISO 228. However, the G inside thread in core and haunch dia has only a positive deviation (from DIN 2999 +/-tolerance). Therefore a DIN 2999 tapered outside thread may be screwed into an ISO 228 parallel inside thread. The outside threadcan be screwed 1 turn further. The likelyhood of leaks occurring is increased due to larger core dia tolerance of the G thread which givesa larger clearance between the points of the threads. In no circumstancescombine ISO 228 parallel G outside thread with DIN 2999Rp parallel inside thread as the inside thread is too small.
Rosca exterior Rosca interior ext. tubo N de vueltas Exterior Engrane Interior
DN Outside Th. R Inside Th. Rp Pipe OD No of Th. P h Outside Haunch Core a i
6 R 1/8" Rp 1/8" 10,2 28 0,907 0,581 9,728 9,147 8,566 4,0 6,5
8 R 1/4" Rp 1/4" 13,5 19 1,337 0,856 13,157 12,301 11,445 6,0 9,7
10 R 3/8" Rp 3/8" 17,2 19 1,337 0,856 16,662 15,806 14,950 6,4 10,115 R 1/2" Rp 1/2" 21,3 14 1,814 1,162 20,955 19,793 18,631 8,2 13,2
20 R 3/4" Rp 3/4" 26,9 14 1,814 1,162 26,441 25,279 24,117 9,5 14,5
25 R 1" Rp 1" 33,7 11 2,309 1,479 33,249 31,770 30,291 10,4 16,8
32 R 1 1/4" Rp 1 1/4" 42,4 11 2,309 1,479 41,910 40,431 38,952 12,7 19,1
40 R 1 1/2" Rp 1 1/2" 48,3 11 2,309 1,479 47,803 46,324 44,845 12,7 19,1
50 R 2" Rp 2" 60,3 11 2,309 1,479 59,614 58,135 56,656 15,9 23,4
2.55
-
7/25/2019 Bsp Rosca Cuerda
3/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
2.56
Rosca de tubo cnica americana conforme ANSI/ASME B 1.20.1 - 1983
American tapered thread to ANSI/ASME B 1.20.1 - 1983
Signo /Abbreviation: NPTDesignacin /Description: 3/8 - 18 NPT
Tipo de rosca /Type: Rosca interior cnica Rosca exterior cnica (Cono 1:16)
Tapered inside Tapered outside (taper 1:16)
Aplicacin /Uses: Rosca de tubo, para tubos roscados y racores para tubo, con estanqueidad en la rosca
mediante agente obturador.Pipe threads, for pipe threads and fittings, sealing in the thread
with sealing material.
Altura de rosca h = 0.8*PAltura del tringulo de perfil H = 0.866*PAplanamiento minimo f =
Paso de rosca P
ngulo de engrane 60
Engrane-
E1
h
H
exteriortubo
Longitud de rosca utilizable i
Plano de referencia L1
1,7
9
Situacin del perfil perpendicular al eje3*P 3*P
Descripcin:
La rosca exterior NPT cnica tiene en el plano de referencia L1 el mismo dimetro exterior, de engrane e interior que la rosca interior
NPT en el comienzo de la rosca, de manera que se puede enroscar manualmente hasta dicho plano de referencia. El apriete fuerte
mediante una herramienta aumenta la longitud de penetracin y confiere estanqueidad al racor con la ayuda de un agente obturador
apropiado (como camo o cinta de tefln). Al ser tanto la rosca interior como la rosca exterior cnicas, aportan ms vueltas de rosca
con efecto estanco y de resistencia a la presin. A travs del pequeo aplanamiento de la rosca se origina slo un camino de fuga
reducido. Las roscas NPT se utilizan cuando tienen que fabricarse uniones roscadas a prueba de fugas con producto impermeabilizan-
te en la rosca
Description:
The tapered NPT outside thread has the same core, haunch and outside dia as the NPT inside thread at the start of the thread so that it
can be screwed in by hand. The torque from the spanner lengthens the tapped hole and seals with the aid of a proprietary sealing
material (eg PTFE tape). As both the inside and outside threads are tapered, the likelyhood of leaks occurring is small.
Rosca exterior tubo Nde vueltas engrane E1
Thread Pipe OD No of Threads P h Haunch E1 L1 i
1/8" NPT 10,287 27 0,941 0,753 9,489 4,102 6,703
1/4" NPT 13,761 18 1,411 1,129 12,487 5,786 10,206
3/8" NPT 17,145 18 1,411 1,129 15,926 6,096 10,358
1/2" NPT 21,336 14 1,814 1,451 19,772 8,128 13,556
3/4" NPT 26,670 14 1,814 1,451 25,117 8,611 13,861
1" NPT 33,401 11 1/2 2,209 1,767 31,461 10,160 17,343
1 1/4" NPT 42,164 11 1/2 2,209 1,767 40,218 10,668 17,9531 1/2" NPT 48,260 11 1/2 2,209 1,767 46,287 10,668 18,377
-
7/25/2019 Bsp Rosca Cuerda
4/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
Rosca conforme a ANSI B 1.1
Thread to ANSI B 1.1
Signo /Abbreviation: UNF / UNDesignacin /Description: ANSI B 1.1 UNF 7/16-20
Tipo de rosca /Type: Rosca interior cilndrica (Tol. 2 B) Rosca exterior cilndrica (Tol.2 A)
parallel inside(Tol. 2 B) parallel outside (Tol. 2 A)
Aplicacin /Uses: Rosca de tubo, para uniones no estancas en la rosca
Pipe fittings, not sealing on the thread
Descripcin:
sta rosca sirve fundamentalmente para uniones mecnicas de racores y vlvulas. La estanqueidad en la unin se consigue mediante
la presin de dos superficies estancas contrapuestas fuera de la rosca y la colocacin de una junta apropiada.
Description:
This thread is mainly used for mechanical connection of fittings. The seal results from the pressing together of two sealing faces outside
the thread and from the use of a proprietary sealing material.
Rosca de tuerca Tol. 2B media Rosca del cuerpo Tol 2A media
Female thread Tol. 2 B Male thread Tol. 2 A
Rosca y n de vueltas Paso de rosca Exterior Engrane Ncleo Exterior Engrane Ncleo
Thread and No of Threads Pitch Min Major OD Haunch Core Outside Haunch Core
P D min D2 max D1 max d max d2 max d3 max
7/16 -20 UNF 1,270 11,112 10,424 10,033 11,079 10,254 9,522
1/2 -20 UNF 1,270 12,700 12,017 11,608 12,667 11,841 11,110
9/16 -18 UNF 1,411 14,288 13,520 13,081 14,252 13,335 12,520
3/4 -16 UNF 1,588 19,050 18,184 17,678 19,012 17,981 17,064
7/8 -14 UNF 1,814 22,225 21,224 20,676 22,184 21,006 19,959
1 1/16 -12 UN 2,117 26,988 25,801 25,146 26,944 25,570 24,3481 3/16 -12 UN 2,117 30,162 28,979 28,321 30,119 28,745 27,523
1 5/16 -12 UN 2,117 33,338 32,154 31,496 33,294 31,920 30,698
1 5/8 -12 UN 2,117 41,275 40,094 39,446 41,229 39,855 38,633
1 7/8 -12 UN 2,117 47,625 46,449 45,796 47,579 46,205 44,983
2.57
H = 0,8660254 P
H1 = 5/8 H = 0,54127 P
h3 = 17/24 H = 0,61343 P
R = H/6 = 0,14434 P
R min = 0,125 P ~ H/7
Tuerca
Cuerpo
Rosca de
la tuerca
Rosca del
cuerpo
-
7/25/2019 Bsp Rosca Cuerda
5/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
2.58
Empalmes y alojamientos roscados
Con estanqueidad metlica mediante canto obturador
Screwed Plugs and Tapped HolesWith metallic seal by sealing edge
Tabla de medidas de los alojamientos
DIN 3852 Parte /Part 1 Parte /Part 2 d3-0,2 d4+0,2 d7+0,2 max. a1 min. b1 min. t1
M 8 x 1,0 12 13,0 8,0 1,0 8,0 13,5
M 10 x 1,0 G 1/8" 14 15,0 10,0 1,0 8,0 13,5
M 12 x 1,5 17 18,0 12,0 1,5 12,0 18,5
G 1/4" 18 19,0 13,2 1,5 12,0 18,5
M 14 x 1,5 19 20,0 14,0 1,5 12,0 18,5
M 16 x 1,5 21 22,0 16,0 1,5 12,0 18,5
G 3/8" 22 23,0 16,7 2,0 12,0 18,5
M 18 x 1,5 23 24,0 18,0 2,0 12,0 18,5
M 20 x 1,5 25 26,0 20,0 2,0 14,0 20,5
G 1/2" 26 27,0 21,0 2,5 14,0 22,0
M 22 x 1,5 27 28,0 22,0 2,5 14,0 20,5
M 26 x 1,5 31 32,0 26,0 2,5 16,0 22,5
M 27 x 2,0 G 3/4" 32 33,0 27,0 2,5 16,0 24,0
M 33 x 2,0 G 1" 39 40,0 33,3 2,5 18,0 27,0M 42 x 2,0 G 1 1/4" 49 50,0 42,0 2,5 20,0 29,0
M 48 x 2,0 G 1 1/2" 55 56,0 48,0 2,5 22,0 31,0
Segn DIN 3852 - Parte 1:
Con rosca mtrica cilndrica
conforme a DIN 13
Empalmes roscados
forma B
Male screwed plug
Form B
Alojamientos
roscados forma X
para empalmes
roscados forma B y C
Tapped Holes
Form X
for screwed plugs
Form B and C
Segn DIN 3852 - Parte 2:
Con rosca BSP cilndrica
conforme a DIN/ISO 228
Canto obturador
to DIN 3852 - Part 1:
with parallel metric thread
to DIN 13
to DIN 3852 - Part 2:
with parallel BSP thread
to ISO 228
-
7/25/2019 Bsp Rosca Cuerda
6/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
Empalmes y alojamientos roscados
Con estanqueidad elastomrica mediante junta blanda
Screwed Plugs and Tapped HolesWith elastomer seal by captive seal
Tabla de medidas de los alojamientos
DIN 3852 Parte /Part 1 Parte /Part 2 d3-0,2 d4+0,2 d7+0,2 max. a1 min. b1 min. t1
M 8 x 1,0 12 13,0 8,0 1,0 8,0 13,5M 10 x 1,0 G 1/8" 14 15,0 10,0 1,0 8,0 13,5
M 12 x 1,5 17 18,0 12,0 1,5 12,0 18,5
G 1/4" 18 19,0 13,2 1,5 12,0 18,5
M 14 x 1,5 19 20,0 14,0 1,5 12,0 18,5
M 16 x 1,5 21 22,0 16,0 1,5 12,0 18,5
G 3/8" 22 23,0 16,7 2,0 12,0 18,5
M 18 x 1,5 23 24,0 18,0 2,0 12,0 18,5
M 20 x 1,5 25 26,0 20,0 2,0 14,0 20,5
G 1/2" 26 27,0 21,0 2,5 14,0 22,0
M 22 x 1,5 27 28,0 22,0 2,5 14,0 20,5
M 26 x 1,5 31 32,0 26,0 2,5 16,0 22,5
M 27 x 2,0 G 3/4" 32 33,0 27,0 2,5 16,0 24,0
M 33 x 2,0 G 1" 39 40,0 33,3 2,5 18,0 27,0
M 42 x 2,0 G 1 1/4" 49 50,0 42,0 2,5 20,0 29,0
M 48 x 2,0 G 1 1/2" 55 56,0 48,0 2,5 22,0 31,0
segn DIN 3852, parte 1:
Con rosca mtrica cilndrica
conforme a DIN 13
Empalmes roscados
con junta blanda
Male screwed plug
with captive seal
Alojamientos
roscados forma X
para empalmes rosca-
dos con junta blanda
Tapped holes
Form X
for studs
with captive seal
segn DIN 3852, parte 2:
Con rosca BSP cilndrica
conforme a DIN/ISO 228
Junta blanda
to DIN 3852 - Part 1:
with parallel metric thread
to DIN 13
to DIN 3852 - Part 2:
with parallel BSP thread
to ISO 228
2.59
-
7/25/2019 Bsp Rosca Cuerda
7/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
2.60
Empalmes y alojamientos roscados
Con estanqueidad en la rosca mediante agente obturador
Screwed Plugs and Tapped HolesWith sealing material on the thread
Tabla de medidas de los alojamientos
DIN 3852 Parte /Part 1 Parte /Part 2 NPT min. b2 min. t3
M 8 x 1,0 5,5 10,0
Rp 1/8" 5,5 9,5
M 10 x 1,0 5,5 10,0
M 12 x 1,0 Rp 1/4" 8,5 13,5
M 14 x 1,5 8,5 13,5
M 16 x 1,5 Rp 3/8" 8,5 13,5
M 18 x 1,5 8,5 13,5
M 20 x 1,5 Rp 1/2" 10,5 16,5
M 22 x 1,5 10,5 16,5
1/8" NPT 6,9 11,6
1/4" NPT 10,0 16,4
3/8" NPT 10,3 17,4
1/2" NPT 13,6 22,6
3/4" NPT 14,1 23,1
1" NPT 16,8 27,8
1 1/4" NPT 17,3 28,3
1 1/2" NPT 17,3 28,3
Empalme roscado:
Segn DIN 3852, parte 1:
Con rosca mtrica cnica con-
forme a DIN 158
Alojamiento roscado:
Con rosca mtrica cilndrica
conforme a DIN 13
Empalmes
roscados
forma C
Male screwed
plugs Form C
Alojamientos
roscados forma
Z
slo para empal-
mes roscados
forma C
Tapped holes
Form Z
only for screwed
plugs Form C
Empalme roscado:
Segn DIN 3852, parte 2:
Con rosca BSP cnica
conforme a DIN 3858
Alojamiento roscado:
Con rosca BSP cilndrica
conforme a DIN 3858
NPT:
Empalme y alojamiento roscado con
rosca NPT cnica conforme a
ANSI / ASME B 1.20.1-1983
Studs
to DIN 3852 - Part 1:
with parallel metric
thread to DIN 158
Tapped Holes
with parallel metric
thread to DIN 13
Studs
to DIN 3852 - Part 2:
with tapered BSP
thread to DIN 3858
Tapped Holes
with parallel BSP
thread to DIN 3858
NPT:
Studs and tapped holes
with tapered NPT thread
to ANSI / ASME B
1.20.1-1983
La rosca interior cilndrica y la rosca exterior cnica tienen las mismas medidas nominales para el dimetro de rosca y el perfil de la rosca que las roscas confor-
me a DIN 2999 Parte 1-ISO 7/1. Las roscas BSP cnicas determinadas en esta norma para uniones de tubera tienen unas longitudes de rosca inferior a las
roscas BSP cnicas conforme a DIN 2999 Parte 1-ISO 7/1, es decir, la distancia del plano de medicin del comienzo de la rosca es en esta norma mas corto
que en DIN 2999 Parte 1-ISO 7/1. La rosca cilndrica interior tiene en esta norma, en sus dimetros exterior, de engrane e interior, solamente discrepancias de
medida positiva y por consiguiente otras tolerancias que en DIN 2999 Parte 1-ISO 7/1. Estas discrepancias originan un enroscamiento mximo de la rosca
cnica macho conforme a esta norma
-
7/25/2019 Bsp Rosca Cuerda
8/92.61
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
Empalmes y alojamientos roscados
rosca UNF con estanqueidad mediante junta trica
Screwed Plugs and Tapped HolesUNF-thread with O-Ring-sealing
UNF i Dilatacin d K E b t
D min. a max. +0,1 1 min. min.
7/16-20 9 21 1,0 12,4 12 2,4 12 14
1/2-20 9 23 1,0 14,0 12 2,4 12 14
9/16-18 10 26 1,0 15,6 12 2,5 13 16
3/4-16 11 32 1,5 20,6 15 2,6 15 18
7/8-14 13 35 1,5 23,9 15 2,6 17 20
1 1/16-12 15 42 1,5 29,2 15 3,3 20 24
1 5/16-12 15 50 2,0 35,5 15 3,3 20 24
1 5/8-12 15 60 2,5 43,5 15 3,4 20 24
1 7/8-12 15 65 2,5 49,8 15 3,4 20 24
Alojamiento roscado conforme
a SAE J 475 - ANSI B1.1
Tapped holes
to SAE J 475 - ANSI B1.1
Empalme conforme
a SAE J 475 - ANSI B1.1
Male screwed plugsto SAE J 475 - ANSI B1.1
-
7/25/2019 Bsp Rosca Cuerda
9/9
Informaciones tcnicas
Technical Informations
Racores con doble anillo | Twin Ferrule Fittings
Materiales Materials
Composicin qumica (general)Chemical Composition (general)
USA Francia Abreviatura DIN N materia sf- C Si Mn Cr Mo Ni Otros
AISI AFNOR Abbreviated DIN numberprima Cdigo mximo not more than other
Material-No.
Normas extranjeras International Standard Aceros austeniticos Austenitic Steels
3 03 Z 1 0 CN F 18 /0 9 X 10 C rN iS 18 9 1.4305 1 0,12 1,0 2,0 17,0 - 19,0 0,6 8,0 - 10,0 S 0,15 - 0,35
304 Z 6 CN 18/09 X 5 CrNi 18 9 1.4301 2 0,07 1,0 2,0 17,0 - 19,0 - 8,0 - 10,0 -
3 04 L Z 2 C N 18 /1 1 X 2 Cr Ni 19 11 1.4306 2L 0,03 1,0 2,0 18,0 - 20,0 - 10,0 - 12,5 -
S32304 SAF 2304 X 2 CrNi N 23 4 1.4362 6 0,03 0,5 1,2 23 - 4 N 0,1
3 21 Z 6 C NT 1 8/ 10 X 6 Cr Ni Ti 1 8 1 0 1.4541 3 0,08 1,0 2,0 17,0 - 19,0 - 9,0 - 12,0 Ti 5 x % C - 0,8
3 16 Z 6 C ND 1 7/ 11 X 5 Cr Ni Mo 1 7 1 2 2 1.4401 4 0,07 1,0 2,0 16,5 - 18,5 2,0 - 2,5 10,5 - 13,5 -
3 16 Z 6 C ND 1 7/ 11 G -X 6 Cr Ni Mo 1 8 1 0 1.4408 4i 0,07 1,0 2,0 16,5 - 18,5 2,0 - 2,5 10,5 - 13,5 -
316 L Z 2 CND 17/12 X 2 CrNiMo 17 13 2 1.4404 4L 0,03 1,0 2,0 16,5 - 18,5 2,0 - 2,5 11,0 - 14,0 -
316 L Z 2 CND 17/13 X 2 CrNiMo 18 14 3 1.4435 5 0,03 1,0 2,0 17,0 - 18,5 2,5 - 3,0 12,5 - 15,0 S 0,025
3 16 Z 6 C ND 1 7/ 12 X 5 Cr Ni Mo 1 7 1 3 3 1.4436 5i 0,07 1,0 2,0 16,5 - 18,5 2,5 - 3,0 11,0 - 14,0 S 0,025
316 Ti Z 6 CNDT 17/12 X 6 CrNiMoTi 17 12 2 1.4571 7 0,08 1,0 2,0 16,5 - 18,5 2,0 - 2,5 10,5 - 13,5 Ti 5 x % C - 0,8
1) a menos que se indique otra cosa, el contenido de fsforo puede ser como mximo del 0,045 % y el de azufre del 0,03 %.1) if not expressly stated, the phosphorus content may not be more than 0.045% and the sulphur content not more than 0.03%.
Propiedades fsicas del aceroReferences on physical properties of some steels
Modulo de Dilatacin Conductivi- Capacidad Resistencia
Tipo de acero Densidad elasticidad a 20C por calor entre 20C y de calor dec. especificia elctrica Capacidad de magnetizacin
Type Density Modulus of Thermal expansion Thermal Specific Heat Electrical Magnetisability
e la st ic it y a t 2 0C be tw ee n 20 C a nd c ap ac it y c ap ac ity R es ist an ce
Abreviatura N 100C 400C a 20C a 20C
Abbreviation Material-No. kg/dm3 kN/mm2 106K-1 W/(mK) J/(kgK) mm2/m
X 5 CrNiMo 17 12 2 1.4401 7,98 200 16,5 18,5 15 500 0,75 no existente not exist
X 6 CrNiMo Ti 17 12 2 1.4571 7,98 200 16,5 18,5 15 500 0,75 no existente not exist
X 2 CrNi N 23 4 1.4362 7,75 200 13,0 14,5 16 470 - existente exist
Propiedades mecnicas a temperatura ambienteMechanical properties at room temperature
Tipo de acero Lmite elstico 0,2% Lmite elstico 1% Resistencia a la traccin Alargamiento de rotura
1.4408 Type 1.4301 0,2%-Permanent 1%-Permanent Tensile Ductile yield
elongation limit elongation limit strength
Longit. Trans. Longit. Trans. Longit. y Trans. Longit. Trans. Longit. Trans.
length breadth length breadth length and breadth length breadth length breadth
Abreviatura N N/mm2) N/mm2) N/mm %
Abbreviation Material-No. min. min. min.
X 5 CrNiMo 17 12 2 1.4401 240 255 270 285 550 bis 700 35 40 43 45
X 2 CrNiMo 17 13 2 1.4404 240 255 270 285 550 bis 700 35 40 43 45
X 2 CrNiMoN 17 12 2 1.4406 280 295 310 325 580 bis 800 30 35 38 40
X 6 CrNiMoTi 17 12 2 1.4571 240 255 270 285 540 bis 690 35 40 43 45
*X 2 CrNi N 234 1.4362 400 - 450 - 600 bis 820 - - 25 -
* Los valores se refieren solamente al material en bruto* Values relate to raw material
A80 mm A5