REDES Y SISTEMAS AVANZADOS DE TELECOMUNICACIONES II
-
Upload
pedro-perez -
Category
Documents
-
view
222 -
download
0
description
Transcript of REDES Y SISTEMAS AVANZADOS DE TELECOMUNICACIONES II
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
REDES Y SISTEMAS AVANZADOS DE TELECOMUNICACIONES II
INFORME DE LABORATORIO TRABAJO COLABORATIVO 2
208004_5 CURSO
ANDREA ESCOBAR CAMILO RAUL VILLOTA PANTOJA
ESTUDIANTES
PABLO GUERRA DIRECTOR DE CURSO
PROGRAMA DE INGENIERIA DE TELECOMUNICACIONES UNIVERSIDAD ABIERTA Y A DISTANCIA
UNAD
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
INTRODUCCIÓN
La evolución de los servicios en telecomunicaciones ha logrado que tecnologías
funcionales durante épocas continúen adaptándose a las necesidades actuales en donde
la velocidad y calidad del servicio priman frecuentemente.
La tecnología MPLS aparece como una adaptación mejorada de tecnologías como ATM,
Frame Relay e incluso X.25, donde sus aplicaciones actuales como Ingeniería de tráfico
(flujos de tráfico independientes para cada usuario), servicios de VPN, y aplicaciones que
requieren calidad de servicio.
Las ventajas que podemos encontrar en esta tecnología incluyen, ahorro de costos
comparado a ATM o Frame Relay, Soporte de QoS, recuperación de desastres con enlaces
redundantes.
El presente informe de laboratorio resume e identifica cada uno de los requisitos para
configurar MPLS sobre un esquema simulado por medio del software emulador GNS3 y
bajo plataforma Cisco.
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
OBJETIVOS
El objetivo principal de este trabajo es documentar la funcionalidad de MPLS sobre una red Cisco,
propiciando al estudiante las habilidades necesarias para la configuración de equipos con los
respectivos protocolos.
Específicos
Configurar dispositivos de enrutamiento con el protocolo OSPF
Configurar los enrutadores con el protocolo MPLS.
Configurar las características para QoS.
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
RESUMEN
Fig1. Esquema de red GNS3
Fig2. Diagrama topológico
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
TABLA DE CONFIGURACIONES
Configuración para IP y MPLS
MPLS4
MPLS4 # config terminal
MPLS4 (config) # ip cef
MPLS4 (config) # mpls label protocol ldp
MPLS4 (config) # mpls ip
Cuando se ha configurado el protocolo que usara el router para realizar la conmutación de
etiquetas (CEF) y su distribución LDP, se procede a realizar la configuración OSPF para poder hacer
el routing interno.
MPLS4 (config) # router ospf 1
MPLS4 (config-router) # mpls traffic-eng router-id loopback0
MPLS4 (config-router) # mpls traffic-eng area 0
MPLS4 (config-router) # network 192.168.1.1 0.0.0.0 area 0
MPLS4 (config-router) # network 192.168.3.0 0.0.0.255 area 0
MPLS4 (config-router) # exit
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
MPLSCore
MPLSCore # config terminal
MPLSCore (config) # ip cef
MPLSCore (config) # mpls label protocol ldp
MPLSCore (config) # mpls ip
MPLSCore (config) # router ospf 1
MPLSCore (config-router) # mpls traffic-eng router-id loopback0
MPLSCore (config-router) # mpls traffic-eng area 0
MPLSCore (config-router) # network 192.168.1.2 0.0.0.0 area 0
MPLSCore (config-router) # network 192.168.4.0 0.0.0.255 area 0
MPLSCore (config-router) # exit
MPLS100
MPLS100# config terminal
MPLS100 (config) # ip cef
MPLS100 (config) # mpls label protocol ldp
MPLS100 (config) # mpls ip
MPLS100 (config) # router ospf 1
MPLS100 (config-router) # mpls traffic-eng router-id loopback0
MPLS100 (config-router) # mpls traffic-eng area 0
MPLS100 (config-router) # network 192.168.1.3 0.0.0.0 area 0
MPLS100 (config-router) # network 192.168.4.0 0.0.0.255 area 0
MPLS100 (config-router) # exit
Configuración de las interfaces de los routers
MPLS4
MPLS4 (config) # interface loopback0
MPLS4 (config-if) # ip address 192.168.1.1 255.255.255.255
MPLS4 (config-if) # exit
MPLS4 (config) # interface f0/0
MPLS4 (config-if) # ip address 192.168.2.2 255.255.255.0
MPLS4 (config-if) # no shutdown
MPLS4 (config-if) # exit
MPLS4 (config) # interface f0/1
MPLS4 (config-if) # mpls ip
MPLS4 (config-if) # ip address 192.168.3.2 255.255.255.0
MPLS4 (config-if) # no shutdown
MPLS4 (config-if) # exit
MPLS4 (config) # ip route 192.168.5.0 255.255.255.0 192.168.3.3
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
MPLSCore
MPLSCore (config) # interface loopback0
MPLSCore (config-if) # ip address 192.168.1.2 255.255.255.255
MPLSCore (config-if) # exit
MPLSCore (config) # interface GigabitEthernet0/0
MPLSCore (config-if) # mpls ip
MPLSCore (config-if) # ip address 192.168.3.3 255.255.255.0
MPLSCore (config-if) # no shutdown
MPLSCore (config-if) # exit
MPLSCore (config) # interface GigabitEthernet0/1
MPLSCore (config-if) # mpls ip
MPLSCore (config-if) # ip address 192.168.4.3 255.255.255.0
MPLSCore (config-if) # no shutdown
MPLSCore (config-if) # exit
MPLSCore (config) # ip route 192.168.5.0 255.255.255.0 192.168.4.0
MPLSCore (config) # ip route 192.168.2.0 255.255.255.0 192.168.3.0
MPLS100
MPLS100 (config) # interface loopback0
MPLS100 (config-if) # ip address 192.168.1.3 255.255.255.255
MPLS100 (config-if) # exit
MPLS100 (config) # interface f0/0
MPLS100 (config-if) # mpls ip
MPLS100 (config-if) # ip address 192.168.4.2 255.255.255.0
MPLS100 (config-if) # no shutdown
MPLS100 (config-if) # exit
MPLS100 (config) # interface f0/1
MPLS100 (config-if) # ip address 192.168.5.2 255.255.255.0
MPLS100 (config-if) # no shutdown
MPLS100 (config-if) # exit
MPLS100 (config) # ip route 192.168.2.0 255.255.255.0 192.168.3.0
Verificando configuración en los tres routers
MPLS4# show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
O 192.168.4.0/24 [110/11] via 192.168.3.3, 00:02:19, FastEthernet0/1
S 192.168.5.0/24 [1/0] via 192.168.3.3
S 192.168.7.0/24 [1/0] via 192.168.2.101
192.168.0.0/32 is subnetted, 3 subnets
C 192.168.0.1 is directly connected, Loopback0
O 192.168.0.2 [110/11] via 192.168.3.3, 00:02:19, FastEthernet0/1
O 192.168.0.3 [110/12] via 192.168.3.3, 00:02:19, FastEthernet0/1
C 192.168.2.0/24 is directly connected, FastEthernet0/0
C 192.168.3.0/24 is directly connected, FastEthernet0/1
MPLSCore# show ip route
Gateway of last resort is not set
C 192.168.4.0/24 is directly connected, GigabitEthernet0/1
S 192.168.5.0/24 [1/0] via 192.168.4.2
S 192.168.7.0/24 [1/0] via 192.168.3.2
192.168.0.0/32 is subnetted, 3 subnets
O 192.168.0.1 [110/11] via 192.168.3.2, 00:07:08, GigabitEthernet0/0
C 192.168.0.2 is directly connected, Loopback0
O 192.168.0.3 [110/2] via 192.168.4.2, 00:07:08, GigabitEthernet0/1
S 192.168.2.0/24 [1/0] via 192.168.3.2
C 192.168.3.0/24 is directly connected, GigabitEthernet0/0
MPLS100# show ip route
C 192.168.4.0/24 is directly connected, FastEthernet0/0
C 192.168.5.0/24 is directly connected, FastEthernet0/1
S 192.168.7.0/24 [1/0] via 192.168.4.3
192.168.0.0/32 is subnetted, 3 subnets
O 192.168.0.1 [110/12] via 192.168.4.3, 00:08:51, FastEthernet0/0
O 192.168.0.2 [110/2] via 192.168.4.3, 00:08:51, FastEthernet0/0
C 192.168.0.3 is directly connected, Loopback0
S 192.168.2.0/24 [1/0] via 192.168.4.3
O 192.168.3.0/24 [110/11] via 192.168.4.3, 00:08:51, FastEthernet0/0
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
PRUEBAS DE CONECTIVIDAD
Configuración de Backup
EL Objetivo del router de Backup es que solo funcione cuando el router central (MPLSCore) no
pueda hacerlo, ya sea por un problema en el propio router o en alguno de sus enlaces.
MPLSB1
MPLSCore (config) # interface loopback0
MPLSCore (config-if) # ip address 192.168.1.4 255.255.255.255
MPLSCore (config-if) # exit
MPLSCore (config) # interface GigabitEthernet0/0
MPLSCore (config-if) # mpls ip
MPLSCore (config-if) # ip address 192.168.4.3 255.255.255.0
MPLSCore (config-if) # no shutdown
MPLSCore (config-if) # exit
MPLSCore (config) # interface GigabitEthernet0/1
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
MPLSCore (config-if) # mpls ip
MPLSCore (config-if) # ip address 192.168.3.4 255.255.255.0
MPLSCore (config-if) # no shutdown
MPLSCore (config-if) # exit
MPLSCore (config) # ip route 192.168.5.0 255.255.255.0 192.168.4.0
MPLSCore (config) # ip route 192.168.2.0 255.255.255.0 192.168.3.0
MPLSCore (config) # ip route 192.168.7.0 255.255.255.0 192.168.3.0
Se utiliza el protocolo OSPF para la realización del Backup, este protocolo será el encargado de
construir la tabla de rutas.
MPLS4
MPLS4 (config-router) # network 192.168.2.0 0.0.0.255 area 0
MPLS4 (config-if) # ip route 192.168.2.100 255.255.255.0 192.168.2.101
MPLS100
MPLS100 (config-router) # network 192.168.5.0 0.0.0.255 area 0
MPLS4# show ip route
O 192.168.4.0/24 [110/2] via 192.168.3.4, 00:00:03, FastEthernet0/1
[110/2] via 192.168.3.3, 00:00:03, FastEthernet0/1
O 192.168.5.0/24 [110/3] via 192.168.3.4, 00:00:03, FastEthernet0/1
[110/3] via 192.168.3.3, 00:00:03, FastEthernet0/1
192.168.0.0/32 is subnetted, 4 subnets
C 192.168.0.1 is directly connected, Loopback0
O 192.168.0.2 [110/2] via 192.168.3.3, 00:00:03, FastEthernet0/1
O 192.168.0.3 [110/3] via 192.168.3.4, 00:00:03, FastEthernet0/1
[110/3] via 192.168.3.3, 00:00:04, FastEthernet0/1
O 192.168.0.4 [110/2] via 192.168.3.4, 00:00:04, FastEthernet0/1
192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks
S 192.168.2.100/32 [1/0] via 192.168.2.101
C 192.168.2.0/24 is directly connected, FastEthernet0/0
C 192.168.3.0/24 is directly connected, FastEthernet0/1
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
Configuración de QoS
Definir clases de tráfico: se utiliza en comando class-map seguido de match-any o mach-all,
MPLS4 (config) # class-map match-all Ethernet
MPLS4 (config-cmap) # match dscp CS1
MPLS4 (config) # class-map match-all Wifi
MPLS4 (config-cmap) # match dscp CS2
MPLS4 (config-cmap) # end
MPLS4 (config) # class-map match-all videoEthernet
MPLS4 (config-cmap) # match mpls experimental 1
MPLS4 (config-cmap) # end
MPLS4 (config) # class-map match-all videoWifi
MPLS4 (config-cmap) # match mpls experimental 2
MPLS4 (config-cmap) # end
Definir politicas QoS: se utiliza el comando policy-map seguido del nombre de la política.
MPLS4 (config) # policy-map marcarEXP1
MPLS4 (config-pmap) # class Ethernet
MPLS4 (config-pmap) # set mpls experimental 1
MPLS4 (config-pmap) # end
MPLS4 (config) # policy-map shapeEthernet
MPLS4 (config-pmap) # class videoEthernet
MPLS4 (config-pmap) # shape peak 500000
MPLS4 (config-pmap) # end
Asignar políticas a las interfaces: se utiliza el comando service-policy.
MPLS4 (config)# interface f0/0
MPLS4 (config-if)# service-policy input marcarEXP1
MPLS4 (config-if)# exit
MPLS4 (config)# interface f0/1
MPLS4 (config-if)# service-policy output shapeEthernet
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
Conclusiones
Esta segunda práctica de laboratorio nos ha permitido conocer más profundamente la tecnología MPLS sobre enrutadores y su funcionamiento en un ambiente simulado por la plataforma GNS3. Es importante resaltar que este tipo de emulación requiere un hardware potente para poder ejecutar al tiempo varios enrutadores Cisco con funcionalidades de enrutamiento, MPLS y QoS es por esto que no todos los integrantes del curso logramos emularlo completamente, sin embargo se logra exitosamente aplicar conocimientos sobre MPLS, OSPF y QoS.
[TRABAJO COLABORATIVO 2 INFORME DE LABORATORIO 2] 20 de Noviembre de 2013
BIBLIOGRAFIA CONFIGURATION EXAMPLES AND TECHNOTES http://www.cisco.com/en/US/tech/tk436/tk428/tech_configuration_examples_list.html
CONFIGURING BASIC MPLS USING OSPF http://www.cisco.com/en/US/tech/tk436/tk428/technologies_configuration_example09186a0080093f23.shtml
CONFIGURING MPLS QOS http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SX/configuration/guide/mplsqos.pdf