SIMPOSIO DE TELECOMUNICACIONES - … · •CONTROLADORES O PANELES •TERMINALES DE OPERACIÓN. 37....
Transcript of SIMPOSIO DE TELECOMUNICACIONES - … · •CONTROLADORES O PANELES •TERMINALES DE OPERACIÓN. 37....
1
SIMPOSIO DE TELECOMUNICACIONES
UNIVERSIDAD DE LOS ANDESMÉRIDA – VENEZUELA27 DE ABRIL DE 2007
2
PLATAFORMA DE TELECOMUNICACIONES EN EDIFICIOS INTELIGENTES
ESTADO DE ARTEIng. Pedro José Calderón Baca
Universidad de San Martín de PorresLima - Perú
3
BUILDING IT
EDIFICIO INTELIGENTE
4
5
6
Cuando se trata de definir, evaluar o certificar un
“BUILDING IT” a veces, se confunde lo que es
AUTOMATIZACIÓN con INTELIGENCIA.
7
Es la habilidad de un dispositivo para adaptarse a los cambios del
medio utilizando óptimamente sus recursos con el fin de solucionar un
problema dado.Es la facultad de conocer y
entender.Es la destreza para la ejecución de
una acción.
AUTOMATIZACIÓN
8
9
Es la habilidad del sistema de reconocer a las personas y de brindarles los servicios que han sido diseñados para esa
persona en particular.
INTELIGENCIA
10
11
¿CUÁL ES LA FINALIDAD DEL BUILDING IT?
Ambiente comfortableEficiente en su operación
Seguridad humana (life safety)Seguridad material (security)
Ahorro de energía
12
BUILDING MANAGEMENT
13
14
SECURITY AND LIFE SAFETY
SEGURIDAD MATERIAL Y SEGURIDAD HUMANA
15
16
COMPUTING AND COMMUNICATIONS
17
18
¿QUÉ ES LO QUE DESEAMOS CONTROLAR, ADMINISTRAR,
GERENCIAR?
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
¿CÓMO ADMINISTRAMOS ESTOS SITEMAS?
34
CADA UNO DE LOS SISTEMAS QUE HEMOS VISTO TIENEN SUS
PROPIOS SENSORES O DISPOSITIVOS DE ADQUISICIÓN
DE DATOS, CUYA LABOR ES MONITOREAR EL ESTADO EN QUE
SE ENCUENTRAN, EN CADA MOMENTO, CADA UNO DE ELLOS.
35
CADA UNO DE ESTOS DISPOSITIVOS DE
ADQUISICIÓN DE DATOS HABLA SU PROPIO LENGUAJE,
POR LO TANTO DEBEMOS INTEGRAR TODOS ESTOS
SISTEMA EN UN SOLO SISTEMA
36
INTEGRACIÓN DE SISTEMASELEMENTOS DE LA
INTEGRACIÓN DE SISTEMAS:
•DISPOSITIVOS DE CAMPO•CONTROLADORES O
PANELES•TERMINALES DE OPERACIÓN
37
38
SensoresControladores
Terminales
39
40
41
ADQUISICIÓN DE DATOS
DISPOSITIVOS DE CAMPO
SENSORIZACIÓN
42
Remota
Portable
Local
43
Hemos visto que estos dispositivos de campo son los
ojos, oídos, nariz y piel del edificio inteligente los cuales
proveen la información necesaria para ejecutar el
control automatizado, centralizado del edificio.
44
Hay dos tipos de dispositivos de campo:Inteligentes.
No inteligentes.
45
CONTROLADORES
46
LOS CONTROLADORES SON LOS EQUIPOS QUE RECIBEN LOS DIFERENTES TIPOS DE
SEÑALES DE LOS SENSORES Y LAS CONVIERTEN A UN SOLO TIPO DE SEÑAL COMPATIBLE CON LAS REDES ETHERNET
47
48
TERMINALES DE OPERACIÓN
49
50
•Software de integración y manejo del sistema completo.•Software de mantenimiento
de funciones.•Integración vía LAN/WAN de
estaciones de operación.•Control remotos de edificios.
51
PROTOCOLOS DE INTEGRACIÓN
52
TIPOS DE LENGUAJE DE LOS SENSORES.
Vía duplicidad de componentes de campo, en
paralelo o puentes.Vía señales eléctricas 0-10V;
0-5V; 4-20mA; 0-50 Ohms.Vía protocolos de
comunicación digital.
53
54
55
56
BACnet: (Building Automation andControls Network).
EIB: (European Installation Bus).CEBus: (Conmsumer Electronics
Bus).LonTalk: (Local Operating
Network, Echelon Corporation).
PROTOCOLOS DE INTEGRACIÓN
57
BACnet
Building Automation andControls Network
58
•Trabaja en los niveles de application, network, data link y
physical layer, de los niveles OSI (open system
interconnection). Trabaja con Ethernet, ARCnet, LonTalk,
Point-to-Point, Master-slave/token-passing.
BACnet Building Automation andControls Network
59
•Este protocolo ha sido diseñado para ser aplicable a
cualquier función de automatización de edificio.
BACnet Building Automation andControls Network
60
•El uso de este protocolo ha sido casi exclusivamente aplicado al
control de HVAC(heating,ventilating, and air-
conditioning), no desarrollado para control de fuego, control de acceso,
iluminación u otro BAS (buildingautomation system).
BACnet Building Automation andControls Network
61
EIB
European Installation Bus
62
•Estándar desarrollado por Siemens.Esta basado en el protocolo
CSMA/CA (carrier sense multipleaccess/collision detection) para
comunicación serial u usando un bus común lo cual reduce el
cableado usando dispositivos en cadena o puente.
EIB European Installation Bus
63
Puede usar cable UTP, infrarrojo, líneas eléctricas, radio frecuencia. Emplea multicast communication. Un simple mensaje puede activar
dozenas o aun cientos de funciones en una red EIB.
EIB European Installation Bus
64
CEBus
Consumer Electronics Bus
65
•Desarrollado por EIA (ElectronicsIndustries Alliance) para LANs y
redes de automatización en casas y residencias.
CEBus (Consumer ElectronicsBus)
66
•Usa arquitectura abierta y trabaja sobre líneas eléctricas, cable UTP, fibra óptica, coaxial,
infrarrojo, radio frecuencia.
CEBus (Consumer ElectronicsBus)
67
LonTalk
Local Operating Network, Echelon Corporation)
68
•LonTalk es un protocolo desarrollado por Echelon
Corporation para el control de interoperabilidad de las redes usando tecnología LonWorks.
LonTalk Local Operating Network, Echelon Corporation)
69
•LonWorks es usado para redes de control distribuida que consiste de dispositivos
inteligentes conectados en conjunto usando cualquier tipo de media: líneas elctricas, cable
UTP, fibra óptica, coaxial, inalámbrico.
LonTalk Local OperatingNetwork, Echelon Corporation
70
Cada dispositivo de la red LonWorks contiene su propio
microrocesador, llamado Neuronchip para emitir señales de
comunicaciónes y su procesamiento.
LonTalk Local Operating Network, Echelon Corporation
71
Este protocolo usa las 7 capas de OSI dando una completa
plataforma de interconexión. Los dispositivos LonTalk de
diferentes fabricantes pueden NO hablar uno con otro, a menos que
hayan sido fabricados bajo el programa LonMark.
LonTalk Local Operating Network, Echelon Corporation
72
•LonTalk es un protocolo abiertoy es totalmente compatible con el
estándar ANSI/ASHARAE 135 BACnet y el ANSI/EIA 709.1-A
Control Network Protocol.
LonTalk Local Operating Network, Echelon Corporation
73
Su uso se adapta para edificios, industrias y casas y lo realiza a
través de redes basadas en internet ó IP-BASED.
Contola todas funciones de automatización por ejemplo HVAC, controles de acceso, control de iluminación, etc.
LonTalk Local Operating Network, Echelon Corporation
74
75
HONEYWELLJHONSON CONTROL
SIEMENSANDOVER CONTROLS
LANDIS & STAEFACSI CONTROL SYSTEM
INTERNATIONALSIEBE (antes BARNER
COLLMAN)
76
PLATAFORMA DE COMUNICACIÓN INALÁMBRICA
77
78
79
80
81
IEEE 802.15 WPAN™ Task Group 4 (TG4)
ZigBee
82
The IEEE 802.15 TG4 was charteredto investigate a low data rate solutionwith multi-month to multi-year battery
life and very low complexity. It isoperating in an unlicensed,
international frequencyband. Potential applications are sensors, interactive toys, smart
badges, remote controls, and homeautomation.
83
ZigBee is a wireless technologydeveloped as an open global standardto address the unique needs of low-
cost, low-power, wireless sensor networks.
84
The standard takes full advantage ofthe IEEE 802.15.4 physical radio
specification and operates in unlicensed bands worldwide at thefollowing frequencies: 2.400–2.484
GHz, 902-928 MHz and 868.0–868.6 MHz.
85
The 802.15.4 specification wasdeveloped at the Institute of Electrical
and Electronics Engineers (IEEE). The specification is a packet-based
radio protocol that meets the needs oflow-cost, battery-operated devices.
The protocol allows devices tointercommunicate and be powered by
batteries that last years instead ofhours.
86
The ZigBee protocol carries allthe benefits of the 802.15.4
protocol with added networkingfunctionality.
87
The ZigBee Protocol
The ZigBee protocol was engineeredby the ZigBee Alliance, a non-profit
consortium of leading semiconductor manufacturers, technology providers,
OEMs and end-users worldwide.
88
The protocol was designed to provideOEMs and integrators with an easy-
to-use wireless data solutioncharacterized by low-power
consumption, support for multiplenetwork structures and secure
connections.
89
The ZigBee Advantage
The ZigBee protocol was designedto carry data through the hostile RF environments that routinely exist in
commercial and industrial applications.
90
ZigBee protocol features:
Low duty cycle - Provides long battery life
Low latencySupport for multiple network
topologies: Static, dynamic, star andmesh
91
Direct Sequence Spread Spectrum(DSSS)
Up to 65,000 nodes on a network128-bit AES encryption – Provides
secure connections between devices Collision avoidance
92
Link quality indicationClear channel assessment
Retries and acknowledgementsSupport for guaranteed time slots
and packet freshness
93
Secure Connections
The ZigBee specification provides a security toolbox approach toensuring reliable and secure
networks. Access control lists, packet freshness timers and 128-bit
encryption based on the NIST Certified Advanced EncryptionStandard (AES) help protect
transmitted data.
94
ZigBee Applications
ZigBee enables broad-baseddeployment of wireless networks with
low-cost, low-power solutions.
95
It provides the ability to run for yearson inexpensive batteries for a host of
monitoring applications: Lightingcontrols, AMR (Automatic Meter
Reading), smoke and CO detectors, wireless telemetry, HVAC control,
heating control, home security, Environmental controls, drapery and
shade controls, etc.
96
Standard ZigBee® 802.15.4
Wi-Fi™802.11b
Bluetooth™
802.15.1 Transmission Range(meters)
1 – 100* 1 - 100 1 – 10
BatteryLife (days)
100 –1,000
0.5 – 5.0 1 - 7
NetworkSize (# of
nodes
> 64,000 32 7
97
Standard ZigBee® 802.15.4
Wi-Fi™802.11b
Bluetooth™
802.15.1 Application Monitoring
& ControlWeb, Email, Video
Cable Replaceme
ntStack Size
(KB)4 – 32 1,000 250
Throughputkb/s)
20 – 250 11,000 720
98
Mesh Networks
A key component of the ZigBee protocolis the ability to support mesh networks.
In a mesh network, nodes are interconnected with other nodes so that
at least two pathways connect eachnode.
99
Connections between nodes are dynamically updated and optimized in difficult conditions. In some cases, a partial mesh network is established
with some of the nodes onlyconnected to one other node.
100
Mesh networks are decentralized in nature; each node is self-routing and
able to connect to other nodes as needed. The characteristics of meshtopology and ad-hoc routing provide
greater stability in changing conditionsor failure at single nodes.
101
102
Performance
Power Output:
XBee: 1mW (0 dBm) XBee-PRO: 60 mW (18 dBm)*, 100 mW EIRP*
Indoor/Urban Range:
XBee: up to 100' (30m) XBee-PRO: up to 300' (100m)
103
Outdoor/RF Line-of-sight Range:
XBee: up to 300' (100m) XBee-PRO: up to 1 mile (1.6km) RF
Data Rate:250 Kbps
104
Interface Data Rate: up to 115.2 Kbps
Operating Frequency: 2.4 GHz
Receiver Sensitivity:
XBee: -92 dBmXBee-PRO: -100 dBm
105
Networking
Spread Spectrum Type: DSSS (Direct Sequence SpreadSpectrum)
Networking Topology: Peer-to-peer, point-to-point & point-to-multipoint
106
Error Handling: Retries & acknowledgements
Filtration Options: PAN ID, channeland addresses
Channel Capacity:
XBee: 16 ChannelsXBee-PRO: 12 Channels
107
Addressing:65,000 networkaddresses available for eachchannel
Encryption:128-bit AES (comingsoon)
108
Power
Supply Voltage:2.8 - 3.4 V
Transmit Current:
XBee: 45 mA (@ 3.3 V) XBee-PRO: 270 mA (@ 3.3 V)
109
Receive Current:
XBee: 50 mA @ 3.3 V XBee-PRO: 55 mA (@ 3.3 V)
Power-down Sleep Current:<10 µA
110
General
Frequency Band:
2.4000 - 2.4835 GHz
Serial Data Interface:
3V CMOS UART - No configurationrequired
111
Physical Properties
Size:
XBee: 0.960" x 1.087" (2.438cm x 2.761cm), XBee-PRO: 0.960" x 1.297" (2.438cm x 3.294 m)
Weight:XBee: 0.10 oz. (3g) XBee-PRO: 0.14 oz. (4g)
112
Weight:
XBee: 0.10 oz. (3g) XBee-PRO: 0.14 oz. (4g)
Antenna Options:
U.FL RF connector, chip antenna, or whip antenna
Operating Temperature:
-40 to 85° C (industrial)
113
Certifications:
FCC:
XBee: OUR-XBEE XBee-PRO: OUR-XBEEPRO
IC:
XBee: 4214A-XBEE XBee-PRO: 4214A-XBEEPRO
114
115
116
Ing. Pedro José Calderón [email protected]