Tubo t8 120 Vultima2

8/13/2019 Tubo t8 120 Vultima2

1/7

D+LED


2/7

D+LEDLEDTubeFeaturesSpecial design of end-cap

Design of removable end-cap provides quick replacement of inner-transformer by pressingthe switch on the end caps easily. Different from other tubes which fixing end-cap by glue, this

new tube designed by our R&D, and it enables customers open the tube to replace

inner-transformer if the transformer fails after some years usage.

Perfect design to avoid led failure in series

Our company invested much in R&D and researched a new technology to make all leds in the

tube work independently. Namely, if one led fails, no impact to other led. However, most led

tube in the market designed with at least 7 leds per series. 1 led doesnt work, all other 6leds

or more not work. Lumen of the whole tube will drop much.

Top quality PC cover

For our tube, both transparent and milky covers are available. For milky cover, when lighten

the tube, LEDS are invisible. Namely, light effect is very even and same as traditional

fluorescent light. We realized 100% perfect replacement.

Great Lighting source

The chip of led is of high quality and bigger size, 10*23 chip, which is from Epistar in Taiwan.

It can resist higher anti-static and distribute more brightness, esp. 3528 SMD LED is at least

2000mcd or 6.5lm-7lm.

Low light attenuation

esp. the white light is adopting new technology, less than 3% in 1000h, however, the

traditional attenuation of white color at least 30%;

Ultra quality inner transformer

We have our own researching and development team to focus on LED driver. The driver we

researched for our tube is Isolate high. PF. Driver and UL approved.

More durable & robust

It can light up to 10 years, comes with 3 years guarantee time.

High safety performance

We have double isolation from our transformer. What is more, our tubes are UL(E344776),

CE, certified and RoHS compliant. With the range of CE, we have passed through EMC and

LVD test, so you can apply the tube for your projects freely.

Tube package

High quality cylindrical package and pin protection avoids shipping damage. Please refermore information on last page about package information.


3/7

D+LED

Drawing

Notes:

1. All dimension units are millimeters.

2. All dimension tolerance is 1mm unless otherwise noted.

ApplicationWidespread use in Family, School, Office, Showing Room, Meeting Room

Commercial Building, Tower, Hotel, Restaurant Factory, Production Line, Warehouse

Pathway lighting, Street lighting Subway station, bus and train


4/7

D+LEDIlluminance

T8-N8W-60/120/150(cool white) T8-N8WW-60/120/150(warm white)

CharacteristicsAbsolute Maximum Rating at TA=25

Parameter Symbol Absolute Maximum RatingT8-N8W-60/120/150 Unit

Working Voltage V AC85-265V V

Power Dissipation PD 8 / 12 / 16 / 18 W

Electrostatic discharge ESD 800 V

Operating Temperature Topr -20+50

Storage Temperature Tstg -3 0 +60

Electrical / Optical Characteristics at TA=25

Length Part No. Color Color Temp. Lumen Power CRI(Typical) Viewing Angle

60cm T01/T8-N8NW-60 Natural white 4000-4500K 840 lm 8W 78 120

120cm T04/T8-N8NW-120 Natural white 4000-4500K 1680 lm 16W 78 120

150cm T06/T8-N8W-150 Cool white 5000-6000K 1875 lm 18W 78 120

Notes: Tolerance of measurement of luminous intensity15%.


5/7

D+LEDInstallationInformationPrecaution: Switch off power before doing any works.Installation for double-ended power tube

Method A

If lighting fixtures wire connection is inductor ballast, installation as bellow.

Step 1. Remove the traditional fluorescent tube from the lighting fixture.

Step 2. Take out the inductor ballast from the lighting fixture.

Step 3. After take out the ballast, there will have two wires. One wire connects to right side

and another wire connects to left side.

Step 4. Install LED fluorescent tube light into lighting fixture.

Before change connection After change connection

Method B

If lighting fixtures wire connection is Electronic ballast, installation as bellow.

Step 1. Remove the traditional fluorescent tube from the lighting fixture.

Step 2. Take out the starter and electronic ballast from the lighting fixture.

Step 3. After take out the ballast, there will have two wires. One wire connects to right side

and another wire connect to left side.

Step 4. Install Torshare Led tube light into lighting fixture.

Before change connection After change connection


6/7

D+LEDInstallation for single-ended power tube

Step 1, Remove the fluorescent lamp.

Step 2, Cut off all wires which connected to inductive ballast or electrical ballast.

Step 3, Connected two wires from the lamp holder. (The additional wire connector and No. 18

AWG wiring maybe required)

Step 4, Connected the two wires to branch circuit L and N.

Step 5, Install LED tube.

Step 6Switch on power.


7/7

D+LEDWarning LED Fluorescent tube and all of its components must not be subjected to mechanical

stress.

The complete installation must be done by an electrical expert who is familiar with the valid

directives.

If any doubt about the installation or use of this product, consult a competent electrician

Don't use it if aluminium of the tube have any damage or distortion. Otherwise, the product

or the installation might not be sufficiently safe!

Switch off power of the mains supply or respectively of the connection lead before doing any

works.

Assembly must not damage or destroy conducting paths.

Make sure that the product is mounted on a stable, even and tilt-fixed background.

Keep away from direct sunshine and high temperature

Indoor use only

PackingInformationLength

Outer Carton Size

(LWHcm

Qty/Carton

pcs

N.W

(kg)

G.W

(kg)

60cm 66*21*29.5 30 8 11

120cm 126.5*21*28 30 13 19

150cm 157*21*28 30 18 24

Tubo t8 120 Vultima2

Documents

Transcript of Tubo t8 120 Vultima2