rodriguezzambrano.files.wordpress.com€¦ · Web viewPrimero que nada vamos a realizar la...
Transcript of rodriguezzambrano.files.wordpress.com€¦ · Web viewPrimero que nada vamos a realizar la...
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
PRACTICA
Introducción
Primero que nada vamos a realizar la siguiente topología, para ello necesitamos algunas herramientas como lo es Packet Tracer este programa nos permite realizar una simulación de conectividad de redes mediante topologías creadas por nosotros mismos, en las cuales vamos configurar los dispositivos, conectar los router mediante los cables requeridos.
En este caso tenemos la topología siguiente (Imagen). Para realizarla como ya lo comente, tenemos que abrir Packet Tracer para dibujar los dispositivos necesarios. En este caso tenemos que ocupar 4 routers, 4 servidores y por último el tipo de cable. Ocuparemos 4 seriales y 4 cruzados.
El cable serial lo vamos a conectar en cada router, tomando en cuenta que se debe llevar un orden en este caso empezare por el router de nombre Movistar. El cable serial se caracteriza por tener un color rojo y de una forma de rayo, lo tomaremos de la parte inferior del Packet tracer, buscamos el cable serial el cual tiene un relojito, lo arrastramos hacia el primer router que se llama Movistar y se conecta el cable en la interface 0/0, de ahí nos pasamos al siguiente router que se llama Telcel, en este caso como ya se conecto la interface s0/0 ahora lo conectaremos en la s0/1. Después hacemos el mismo procedimiento con los siguientes routers, en el router Telcel de igual manera arrastramos el cable tomamos la s0/0 y nos pasamos al otro router llamado Iusacell y conectamos en la s0/1.
Después de hacer esto con todos los routers pasaremos a conectar los servidores en cada router, para estos se utiliza el cable cruzado que se caracteriza por ser una línea punteada, de la misma manera buscamos el cable en la parte inferior y arrastramos hacia el router y ahí le damos en la fa0/0, así mismo en el servidor lo ponemos en la Fast Ethernet, este mismo procedimiento es para conectar los demás servidores.
Estas son las principales herramientas que utilizamos para diseñar una topología. El otro tipo de herramienta es la configuración con los comandos necesarios. Que son los que se muestran a continuación (Nombre de router, Levantamiento de interfaces, Enrutamiento, Contraseñas, Ping, Telnet).
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
Primer Router (Movistar)
Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname MovistarMovistar(config)#interface s0/0Movistar(config-if)#ip address 140.0.0.1 255.255.255.252Movistar(config-if)#no shutdownMovistar(config-if)#clock rate 56000%LINK-5-CHANGED: Interface Serial0/0, changed state to downMovistar(config-if)#exit
Movistar(config)#interface s0/1Movistar(config-if)#ip address 140.0.0.10 255.255.255.252Movistar(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/1, changed state to downMovistar(config-if)#exit
Movistar(config)#interface fa0/0Movistar(config-if)#ip address 140.0.2.1 255.255.254.0Movistar(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
JOEL RODRÍGUEZ ZAMBRANO
TOPOLOGIA
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upMovistar(config-if)#exit
Movistar(config)#interface s0/2Movistar(config-if)#ip address 140.0.0.13 255.255.255.252Movistar(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/2, changed state to down
Movistar(config-if)#clock rate 56000
Movistar(config-if)#exit
ENRUTAMIENTO
Movistar(config)#router EIGRP 100Movistar(config-router)#network 140.0.0.0Movistar(config-router)#network 140.0.0.8Movistar(config-router)#network 140.0.0.12Movistar(config-router)#network 140.0.2.0Movistar(config-router)#exit
CONTRASEÑAS
Movistar(config)#enable secret classMovistar(config)#enable password ciscoMovistar(config)#line console 0Movistar(config-line)#password ciscoMovistar(config-line)#loginMovistar(config-line)#exitMovistar(config)#line vty 0 4Movistar(config-line)#password ciscoMovistar(config-line)#loginMovistar(config-line)#exitMovistar(config)#^Z%SYS-5-CONFIG_I: Configured from console by consoleMovistar# copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Movistar#
Segundo Router (Telcel)
Press RETURN to get started!
Router>enableRouter# configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname TelcelTelcel(config)#interface s0/0Telcel(config-if)#ip add 140.0.0.9 255.255.255.252Telcel(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/0, changed state to upTelcel(config-if)#clock rate 56000
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
Telcel(config-if)#exit
Telcel(config)#interface s0/1Telcel(config-if)#ip add 140.0.0.6 255.255.255.252Telcel(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/1, changed state to downTelcel(config-if)#exit
Telcel(config)#interface fa0/0Telcel(config-if)#ip add 140.0.0.17 255.255.255.240Telcel(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upTelcel(config-if)#exit
ENRUTAMIENTO
Telcel(config)#router EIGRP 100Telcel(config-router)#network 140.0.0.16Telcel(config-router)#network 140.0.0.4Telcel(config-router)#network 140.0.0.8Telcel(config-router)#exit
CONTRASEÑAS
Telcel(config)#enable secret classTelcel(config)#enable password ciscoTelcel(config)#line console 0Telcel(config-line)#password ciscoTelcel(config-line)#loginTelcel(config-line)#exitTelcel(config)#line vty 0 4Telcel(config-line)#password ciscoTelcel(config-line)#loginTelcel(config-line)#exitTelcel(config)#^Z%SYS-5-CONFIG_I: Configured from console by consoleTelcel# copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Telcel#
Tercer Router (Iusacell)
Press RETURN to get started!
Router>enableRouter#configure terminalConfiguring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname IusacellIusacell(config)#interface s0/0Iusacell(config-if)#ip add 140.0.0.5 255.255.255.252Iusacell(config-if)#no shutdown
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
%LINK-5-CHANGED: Interface Serial0/0, changed state to upIusacell(config-if)#exit
Iusacell(config)#interface s0/1Iusacell(config-if)#ip add 140.0.0.2 255.255.255.252Iusacell(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/1, changed state to upIusacell(config-if)#exit
Iusacell(config)#interface fa0/0Iusacell(config-if)#ip add 140.0.0.33 255.255.255.240Iusacell(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upIusacell(config-if)#exit
ENRUTAMIENTO
Iusacell(config)#router EIGRP 100Iusacell(config-router)#network 140.0.0.32Iusacell(config-router)#network 140.0.0.4Iusacell(config-router)#network 140.0.0.0Iusacell(config-router)#exit
CONTRASEÑAS
Iusacell(config)#enable secret classIusacell(config)#enable password ciscoIusacell(config)#line console 0Iusacell(config-line)#password ciscoIusacell(config-line)#loginIusacell(config-line)#exitIusacell(config)#line vty 0 4Iusacell(config-line)#password ciscoIusacell(config-line)#loginIusacell(config-line)#exitIusacell(config)#^Z%SYS-5-CONFIG_I: Configured from console by consoleIusacell#copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Iusacell#
Cuarto Router (Nextel)
Press RETURN to get started!Router>enableRouter#configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#hostname NextelNextel(config)#interface s0/0Nextel(config-if)#ip address 140.0.0.14 255.255.255.252Nextel(config-if)#no shutdown%LINK-5-CHANGED: Interface Serial0/0, changed state to up
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
Nextel(config-if)#exitNextel(config)#interface fa0/0Nextel(config-if)#ip address 140.0.0.129 255.255.255.128Nextel(config-if)#no shutdown%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to upNextel(config-if)#exitENRUTAMIENTO
Nextel(config)#router EIGRP 500Nextel(config-router)#network 140.0.0.12Nextel(config-router)#network 140.0.0.128Nextel(config-router)#exit
CONTRASEÑAS
Nextel(config)#enable secret classNextel(config)#enable password ciscoNextel(config)#line console 0Nextel(config-line)#password ciscoNextel(config-line)#loginNextel(config-line)#exitNextel(config)#line vty 0 4Nextel(config-line)#password ciscoNextel(config-line)#loginNextel(config-line)#exitNextel(config)#^Z%SYS-5-CONFIG_I: Configured from console by console
Nextel# copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Nextel#
CONECTIVIDAD
[TELNET]
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
[PING]
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
[Contraseña]
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
[Enrutamiento]
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
[Interfaces]
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
Conclusión
Bueno como su nombre lo dice, Práctica obviamente nos sirve para incrementar el aprendizaje en lo que es la configuración y el direccionamiento en una topología a través de protocolos, en este caso el protocolo EIGRP. Se realizaron los 5 pasos generales para sacar los saltos para los host de cada servidor, el direccionamiento, la configuración de cada una de las interfaces, el ingreso de las contraseñas y el enrutamiento a través de este protocolo.
Esto nos ayudó para reafirmar los conocimientos que ya se aprendieron a lo largo de las clases. Este tipo de prácticas son de gran ayuda porque si se tienen algunas dudas, dentro de Packet Tracer las podemos resolver y es mucho más fácil porque es de una manera grafica y accesible para mí.
JOEL RODRÍGUEZ ZAMBRANO
UNIVERSIDAD TECNOLÓGICA DE IZÚCAR DE MATAMOROS 2 “A” TIC-SI
JOEL RODRÍGUEZ ZAMBRANO