New Sensor Network TechnologyAnyWire for wiring saving
POKAYOKE Terminal series catalog
POKAYOKE Sho-Haisen SystemPOKAYOKE Terminal series
ProductsPOKAYOKE Terminal series
・・・・・
・・・・・・・・・・・・ 07・システム構成
・・・・
・・・・・・・・・・・・・・・・・・・・・・・・
・・・・・・・・
・・・・・・・・・・
・・・・・・・・・・・・・・
・・・・・・・・・・・・・・
・・・・・・・・・・・・
・・・・
・・・・・・・・・・・・
09
10
0202
11
12
22
23
25
27
02
POKAYOKE terminal selection procedure
Basic transmission specification of system
・・・・・・・・・・・・
・・・・・・
・・・・・
・・・・・・
03
05
08
・Case example of application
◇System Overview
・・・・ 02
02
・What is the POKAYOKE terminal?
・Reason to select AnyWire (1 to 3)
・System configuration and selection procedure
◇Product variation
・Product list (Matrix diagram)
・Product details page
・Accessories
・Master units
・Address setting
・Dimensional outlines drawing (3-view drawing)
POKAYOKE
Terminal series catalog
Table of Contents
POKAYOKE Terminal series01
POKAYOKE Terminal series
POKAYOKE Terminal seriesConcept
02
What is the POKAYOKE terminal?
After
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
ADDRESS
ON
POKAYOKE Terminal System
POKAYOKE Terminal System
After
Conventional System
Before
Before
When you install the POKAYOKE system,
“Picking” work to select parts from inventory according to instruction is carried out at
production sites where parts are assembled. Increase in types of parts also increases
risks to incorrectly pick parts of similar shape and approximate part name, which is a
major problem at production sites.
“Picking” on assembly/production sites
Control of human errors in picking work is an essential element for enhancement and
improvement in production ef�ciency and product quality. Systems and devices to
prevent such human-induced careless mistakes (poka) are called “POKA-YOKE,” and
currently some overseas production sites have adopted the Japanese-derived term
“POKA-YOKE,” to indicate the importance of this manufacturing challenge.
“POKA-YOKE” is a global common word
The “POKAYOKE system” comprising the AnyWire POKAYOKE terminal represents a solution to this problem simply and at low
cost. There is no need to look for parts with a list in one hand, and no errors occur in parts and quantity.
In addition, these POKAYOKE terminals into which AnyWire’s unique Sho-Haisen technology is integrated offer many advantages
such as freedom of installation, easy wiring work, �exibility in change and remodeling, and dif�culties in introduction can be
lowered.
◇ As the location of parts is informed by LED lamps, parts can be clearly identified even in a dark warehouse.
◇ As only the door for location from which parts should be taken out opens, retrieval errors never occur.
◇ As the quantity of parts is clearly instructed by 7-segment indication, errors in quantity never occur.
“POKAYOKE” terminal of AnyWire
Before & After
Conventional System
At an Automotive Assembly Site!At an Automotive Assembly Site!
At an Electronics Equipment Assembly Site!At an Electronics Equipment Assembly Site!
Time and effort required to read a list and instructionsDo not know as to where actual parts areBecomes one-handed operationTime required to assembleIncorrect parts assembly occurs
No need to read a list or instructionsKnow where actual parts are at onceCan operate with both handsAssembly time reducedQuality improved with correct parts assembly
<Take-out>Application 1
POKAYOKE terminal for “Take-out” process
<Throw-in>Application 2
ApplicationsPOKAYOKE Terminal series
POKAYOKE Terminal series03
The f i rs t appl icat ion is “take-out.”
“High-mix and low-volume production” is typically the case at current production sites, and “take-out” is inevitably a major point to increasing production effi-ciency and stabilizing prod-uct quality.
Adoption of the POKAY-OKE terminal can signifi-cantly reduce work man-hours, eliminate errors in take-out of parts and also reduce worker stress.
POKAYOKE terminal for “Throw-in” process
The second application is “Throw-in.”
“Throw-in” always exists at product ion s i tes where “Take-out” exists.The POKAYOKE terminal is also used to prevent errors in “Throw-in” of parts.
Adoption of the POKAY-OKE terminal can secure confirmation of throw-in of parts. It is recommended to introduce the POKAYOKE terminal for “throw-in” in conjunction with “take-out.”
<Kitting: Tray service>Application 4
POKAYOKE Terminal series
POKAYOKE Terminal seriesApplications
04
<Cell production>Application 3
POKAYOKE terminal for “Cell production”
The third application is “cell production.”
The “cell production” method has become more common at production sites of “High-mix and low-volume production.”In this method in which one worker is in charge of the initial to the end of the assem-bly process, there are multiple processes, and if the worker makes any mistake, it is hard to make up for it.
Very small type which can be installed at a narrow opening and the end sur face o f a column plate is available in the POKAYOKE terminal lineup, and is also most suitable for cell production.
POKAYOKE terminal for “Kitting: Tray service” process
The fourth application is “Kitting: Tray service.”
Work in which parts which are necessary for manufac-turing of a certain product are collected in one box (kit box) as one kit is called “kitting.”
The ultimate objectives of the take-out process and kitting are the same, how-ever, detailed work instruc-tions such as quantity and sequence of take-out are required for kitting.
POKAYOKE terminal is also used at such kitting sites.
Reason to select AnyWire 1
ADDRESS No.
LINK
128
2
16
6432
84
1
ADDRESSON
MASTER UNITA027XB-02G2-P
ADDRESS No.
LINK
128
2
16
6432
84
1
ADDRESSON
MASTER UNITA027XB-02G2-P
Standard typeLever switch method
Indication: LED (Green single color indication)Response: Lever switch
Most standard POKAYOKE terminal
LINK
128
2
16
6432
84
1
ADDRESSON
MIX TERMINALA027XB-02GN2-P
LINK IN R/WA027XB-K02V-P
LINK IN R/WA027XB-K71M2-P
LINK IN R/WA027XB-K71MN-P
LINK IN R/WA227XB-K02VL-P-H1
Variation inresponse
and detection
Variation inresponse
and detection
Variation indownsizingVariation indownsizing
Response: Pushbutton
Indication:LED displayResponse:Lever switch
Indication:7-segment indicationResponse:Lever switch
Indication:LED displayResponse: Pushbutton
Indication:7-segment indicationResponse: Pushbutton
Detection: Photoelectric re�ection
248
3216
1
SPDADD
ADDR
ESS
ON
MIX TERMINALA227XB-73MN-P
A027XB-F02G3-PMIX TERMINAL
No.
Variation inindication
and instruction
Variation inindication
and instruction
Indication: 7-segment indication
Indication: LED (7-color indication) Standard compact type
(Standard smallness)
Instruction: Door opening/closing
PIC
KIN
G T
ERM
INAL
A027
PB-T
02G
-P
2841
ON
128643216
ADDR
ESS
PICKIN
G TER
MIN
ALA027XB-T02G
-C
2841
ON
128643216
ADDRESS
Detection: Photoelectric transmission
SUS pipe installation holderPipe installation example
248
3216
1
SPDADD
ADDR
ESS
ON
MASTER UNITA027XB-02GL-P
No.
ADVANTAGE ①
Wide lineup variety!Total 60 or
more models
Installation method
also flexible!
*For standard compact (standard smallness) type, products other than the above are also available. Refer to the pages of the product list for details.
Most POKAYOKE terminals can be installed on a 28mm diameter pipe rack as they are. Three types of pipe installation holders are available depending on workability at the time of installation (refer to the “Installation” at the right for details).Depending on the product, there is also a type to drill at the installation location and directly install with screws or bolts, or a thin type to �x to the end surface of the column plate for a parts shelf with double-sided tape.
AdvantagePOKAYOKE Terminal series
POKAYOKE Terminal series05
BasicBasic7-segment7-segment
PhotoelectrictransmissionPhotoelectrictransmission
Opening/closing of door
Opening/closing of door
SmallnessSmallness
InstallationInstallation
SUS companyN seriesGreen frameCompatible with (outer diameter 28mm)
“H” holder “H1” holder
“SUS” holder
This is the most standard POKAYOKE terminal
with “LED indication,” “Lever switch” and
“Pipe installation.” This is our best seller due
to its simplicity.
If you are considering which type to buy, select this
type.
This type uses the 7-segment for indication. Use this
product when you require indication of numerical
values such as the number of parts. Products of one
digit indication and three digit indication are available
and a lever switch and pushbuttons are available for
a response, allowing you to select your preference.
When parts are long, and
openings are wide or you
wait to detect by take-out
operation and eliminate
r e s p o n s e o p e r a t i o n ,
“Photoelectric transmission
type” is optimal.
H o l d e r f o r p i p e
installation product can
be selected from the
following three types.
“H” is a standard mounting holder, and is the easiest installation type due to the installation bolts being tightened from the front. There is a protruding section to the structure at the bottom of the holder.
“H1” has no protrusion at the bottom of the holder, and is a type for which the bolt is tightened from the bottom (there is a protrusion on the back).
→Add “-H1” at the end of the standard model.
“SUS” is a dedicated holder installed on aluminum pipe of SUS company.
→Change the end of the standard model from “-P” to “-PS.”
POKAYOKE terminal instructs on the take-out
location by opening/closing of door block openings
from which parts should not be taken out. This is
most effective for prevention of mistake.
Response is performed by lever switch.
Products which are signi�cantly downsized compared with
the conventional type have also been added to the lineup.
Various types such as “LED only” type and “7-segment”
type for indication and types equipped with a “buzzer,”
and types such as a “ lever swi tch” and
“pushbutton” for response are available.
Reason to select AnyWire 1
POKAYOKE Terminal series
POKAYOKE Terminal seriesAdvantage
06
Reason to select AnyWire 2
ADVANTAGE ②
Compatible with various
controller networks!
MELSEC sequencer manufactured by Mitsubishi Electric Corporation
・MELSEC-Q series・MELSEC-L series・MELSEC-F series
PLC, controller of each company・Yokogawa Electric FA-M3series ・OMRON CJ1&CS1series・TOSHIBA S2T ・Fuji Electric SX ・Panasonic FPΣ ・Digital LT3000・SHARP JW20/30/300 ・YASKAWA Electric MP2000/3000
Various open networks, PC I/F・CC-Link(Ver.1.10/Ver.2.00) ・DeviceNet・MECHATROLINK I/II/III・PCI Bus ・PC104 ・RS-232C ・RS485Modbus
MELSEC-Qseries
MELSEC-Lseries
MELSEC-Fseries
CJ1/CJ2series
FA-M3series
CS1/CS2series
S2Tseries
SXseries
FPΣseries
LT3000series
JW20/30/300series
MP2000/3000series
CC-Link Ver.1.10CC-Link Ver.2.00DeviceNetMECHATROLINK-I/IIMECHATROLINK-IIIPCI BusPC104RS-232C
Yokogawa Electric
OMRON
TOSHIBAFuji ElectricPanasonicDigitalSHARPYASKAWA Electric
Open network
PC I/F
RS485Modbus
○ ー○ ーー ○○ ー○ ー○ ー○ ー○ ー○ ー○ ー○ ー○ ー
DB A20seriesAnyWire ー ○*
○ ○○ ー○ ○ー ○ー ○○ ー○ ー○ ー○ ー
DB A20 Bitty
Mitsubishi Electric
MELSEC-LMELSEC-Q MELSEC-F
Because the AnyWire POKAYOKE terminal compatible with PLCs of each company including the MELSEC
sequencer of Mitsubishi Electric and many common industrial open networks can be used with general
equipment, environments and tools, there are no concerns even with the initial introduction.
Some products of the AnyWire POKAYOKE terminals are compatible with the “AnyWire DB A20 series”
and some are compatible with the “AnyWire Bitty series.” There is no difference in the performance of the
POKAYOKE terminals, however, there are master units and gateways compatible with each of them. Use
the terminal of the corresponding combination based on the table below.
*Transmission of “Bitty series” can be connected to a low order of transmission of the “DB A20 series” by using a bridge “AB07-A-V3.” → Refer to page 24.
AdvantagePOKAYOKE Terminal series
POKAYOKE Terminal series07
ADVANTAGE ③
Of course, Sho-Haisen!
Easy branching!
Slimmed-down!
Conventional method Sho-Haisen method
Bundle of cables is on controller side···
Address setting!
Appearance ofARW-04
Remote headAppearance ofARW-RH
- Branching can be made even in the middle of wiring because of crimping.
- No waste is produced because an electric wire is not cut/sheath is not stripped.
- There is no difference between male and female, and are the same models, so it is easy to understand.
You can sandwich wire in a sleeve even in the middle or at the end of an electric wire.
Clamp with a dedicated tool to crimp.(See the accessory items.)
T-branch, 4-branch or extension is allowed.Working time is signi�cantly reduced.
The POKAYOKE terminal which “AnyWire of
Sho-Haisen” delivers is of course “POKAYOKE
[Sho-Haisen] terminal.”
Connection can be made only by
branching from the main l ine
without requiring connection of
ind iv idua l termina ls wi th a
controller in one-to-one wiring.
Transmission line of the POKAYOKE terminal is equipped with a link connector (LP connector) as standard. The link connector allows for branching and extension work without electric wire cutting and sheath stripping. Work time can also be reduced, and no electric wire or sheath waste, etc., is produced.
To set the address of the POKAYOKE terminal, a DIP switch or address writer can be selected depending on the product.Refer to pages 25 and 26 for address setting. Refer to and c o n � r m b y t h e p r o d u c t instruction manual of each product for details of each product.
Name of each part of ARW-04
Ring for strap
Position of light emitting and receiving part
(yellow part)
POWER indication lamp
Comment indication part (7-segment 6 digits)
RH (Remote head)
Connection connector (Side)
POWER (CLEAR) button
R button
DOWN button
SELECT button
UP button
L button
SET button
Operation mode indication lamp
Reason to select AnyWire 3
POKAYOKE Terminal series
POKAYOKE Terminal seriesAdvantage
08
Configuration of POKAYOKE system
MELSEC-L
Terminator(Waveform forming module)
MELSEC-Q
Selection of master unit
Terminator
Selection of terminal
Connector and cable
MELSEC-Qseries
MELSEC-Lseries
MELSEC-Fseries
CJ1/CJ2series
FA-M3series
CS1/CS2series
S2Tseries
SXseries
FPΣseries
LT3000series
JW20/30/300series
MP2000/3000series
CC-Link Ver.1.10CC-Link Ver.2.00DeviceNetMECHATROLINK-I/IIMECHATROLINK-IIIPCI BusPC104RS-232C
Yokogawa Electric
OMRON
TOSHIBAFuji ElectricPanasonicDigitalSHARPYASKAWA Electric
Open network
PC I/F
RS485Modbus
○ ー○ ーー ○○ ー○ ー○ ー○ ー○ ー○ ー○ ー○ ー○ ー
DB A20seriesAnyWire ー ○*
○ ○○ ー○ ○ー ○ー ○○ ー○ ー○ ー○ ー
DB A20 Bitty
MitsubishiElectric
MELSEC-F
DC24V
Reference: pages 07, 23, and 24
Con�guration of the POKAYOKE system requires a “Master unit” and “Terminator” in addition to the POKAYOKE terminal,
and an “electric wire” and “connector” connecting them, and “24V DC stabilized power source.”
N a r r o w d o w n t h e P O K A Y O K E terminals you want to use wi th reference to features of individual p roduc ts such as “ ind ica t ion , instruction,” “response, detection” and “how to i ns ta l l , ” and s i t e e n v i r o n m e n t a n d p u r p o s e f o r introduction.It is also necessary to pay attention to the “transmission protocol” and “address setting method” at that time.
Select the master unit to be used for your POKAYOKE system according to the sequencer and open network to be (schedule) used.
When the master unit has been determined, transmission protocol w h i c h y o u c a n u s e i s a l s o de te rm ined , t hen se l ec t t he P O K A Y O K E t e r m i n a l t h a t corresponds to the protocol.Although two types of transmission protocol are not compatible with each other, the transmission line of the Bitty series can be connected t o t h e l o w e r p o s i t i o n o f t h e transmission line of the DB A20 series via a bridge.
A l l POKAYOKE te rmina ls a re shipped with a link connector (LP connector) connected.The LP connector is a crimp type connector with no dist inct ion between female and male, and the branch point can be provided at any location without cutting the main line.If a “4-core �at cable” which is the same as that used for the terminal i s used , w i r i ng wo rk can be performed easily and quickly.
The AnyWire Terminator is different from “Terminal resistor” in general, and incorporates a circuit to form a transmission waveform. Make sure to install one piece in one system at the most remote end of the branch.
“Number of occupied points” and “consuming current” vary with each product, which causes the number of connectable units to vary.Suf�ciently con�rm the speci�cations referring to the catalog and Product Guide (Product instruction manual) to determine the con�guration.
*Products of different protocols cannot be combined for use.
*Even if products of different address setting methods are combined, operation can be performed. However, mistakes may result at the time of setting work, therefore, it is not recommended.
*A compatible l ineup for every product feature can be con�rmed in the product matrix diagram on pages 05 and 06, and page 11.
*Preparation is under way so that Product Guide of the POKAYOKE terminals can be downloaded from our website.
Contact the support dial described at the end of the manual until preparation is completed.
*Transmission of “Bitty series” can be connected to a low order of transmission of the “DB A20 series” by using a bridge “AB07-A-V3.”
System ConfigPOKAYOKE Terminal series
POKAYOKE Terminal series09
POKAYOKE Terminal series
POKAYOKE Terminal seriesSpecification
10
DB A20 series basic transmission specifications
Bitty series basic transmission specifications*Specifications of the Bitty series when the POKAYOKE terminal is used. There are some limits relative to the specifications of the normal Bitty series.
*Specifications of the DB A20 series when the POKAYOKE terminal is used. There are some limits relative to the specifications of the normal DB A20 series.
Contents
59 kbps/1024 points (at transmission clock: 31.3kHz)
Double duplex total frame/cyclic system
Frame/bit synchronization system
1 bit – 512 bits
Bus type (multi-drop type, T-branch type, star type, tree type)
Exclusive protocol (AnyWire Bus protocol)
Double collation system
1024 points (IN 512 points + OUT 512 points)
128 terminals
[0.7ms/128 points] [1.2ms/256 points] [2.2ms/512 points] [4.3ms/1024 points]
Branch disconnection detection, transmission line short-circuit detection
Max. 200m
Exclusive �at cable 0.75mm2 (D, G, 24V, 0V)
Item
Effective data transmission rate
Transmission method
Synchronization system
Data length/frame
Connection mode
Transmission protocol
Error control
Maximum number of connected terminal blocks Note 2)
RAS function
Transmission distance (total length)
Maximum number of connecting I/O points Note 1)
Maximum cycle time Note 3)
Transmission cable
50 kbps/512 points (at transmission clock: 27kHz), 57 kbps/512 points (at transmission clock: 31.3kHz)
Double duplex total frame/cyclic system
Frame/bit synchronization system
1 bit – 256 bits
Bus type (multi-drop type, T-branch type, tree type)
Exclusive protocol (AnyWire Bus Bitty protocol)
Double collation system
Open Terminal series 512 points (IN 256 points + OUT 256 points)
Bitty Bridge 512 points (Bit-Bus IN 256 points + OUT 256 points)
128 terminals
[3.2ms/128 points] [5.5ms/256 points] [10.2ms/512 points](at 31.3kHz)
Transmission line disconnected position detection, Transmission line short-circuit detection
Exclusive �at cable 0.75mm2 (DP, DN, 24V, 0V)
100m(Max)
Item
Effective data transmission rate
Transmission method
Synchronization system
Data length/frame
Connection mode
Error control
Maximum number of connected terminal blocks Note 2)
RAS function
Transmission cable
Transmission protocol
Maximum number of connecting I/O points Note 1)
Maximum cycle time Note 3)
Transmission distance (total length)
Contents
Note 1) Maximum number of transmittable points depends on the master unit. There is a limit to the range of the number of points used according to the speci�cations of the POKAYOKE terminal.
Note 2)There is a limit to the maximum number of connecting units according to the number of occupied points of POKAYOKE terminal used and consuming current value.Note 3) The above described number of points is a representative example of IN, OUT total. The actual cycle time varies depending on the master unit.
Note 1) Maximum number of transmittable points depends on the master unit. There is a limit to the range of the number of points used according to the speci�cations of the POKAYOKE terminal.
Note 2)There is a limit to the maximum number of connecting units according to the number of occupied points of POKAYOKE terminal used and consuming current value.Note 3) The above described number of points is a representative example of IN, OUT total. The actual cycle time varies depending on the master unit.
Indication, instruction method
Response, detection method
LED
ind
icat
ion
onl
y
Sta
tiona
ryty
pe
(Gre
en)
*LED of products marked with is indicated in orange.
A027XB-02G3-P φ28A027XB-E02G3-P φ28
A227XB-02G3-P φ28
A027XB-02G2-P φ28 1 2
A227XB-02G2-P φ28 1 2
A027XB-02GN2-P φ28 1 2
A227XB-02GN2-P φ28 1 2
A027XB-02GN3-P φ28
A227XB-02GN3-P φ28A227XB-02GL2-P φ28 1 2
A027XB-02GL3-P φ281 2A027XB-02GL2-P φ28
A227XB-02GL3-P φ28
A092XB-02GL A027PB-01G-P φ28 1 2
A227PB-01G-P φ28 1 2
A027PB-T02G-P M3
A027XB-T02G-C M3
A227PB-T02G-P M3
A227XB-T02G-C M3
A027PB-T07P02D-P M4
A027XB-T07P02D-C M4
A027PB-T14P02D-P M4
A027XB-T14P02D-C M4
A227PB-T07P02D-P M4
A227XB-T07P02D-C M4
A227PB-T14P02D-P M4
A227XB-T14P02D-C M4
A027XB-K02V-P φ28A227XB-K02V-P φ28
A027XB-K02VN-P φ28A227XB-K02VN-P φ28
A227XB-K06MN-P φ28φ28A027XB-K06MN-P
A227XB-K06M-P φ28
A027XB-06M2-P φ28 1 2
φ28A027XB-K06M-P
A027XB-F02G3-P φ28A227XB-F02G3-P φ28
A027XB-K71V-P φ28A227XB-K71V-P φ28
A027XB-K71VN-P φ28A227XB-K71VN-P φ28
→Refer to page 12 for details.
→Refer to page 12 for details.
→Refer to page 12 for details.
→Refer to page 16 for details.
→Refer to page 17 for details.
→Refer to page 17 for details.
→Refer to page 19 for details.
→Refer to page 19 for details.
→Refer to page 13 for details.
→Refer to page 13 for details.
→Refer to page 13 for details.
→Refer to page 18 for details.
→Refer to page 18 for details.
→Refer to page 19 for details.
→Refer to page 19 for details.
→Refer to page 14 for details.
→Refer to page 19 for details.
→Refer to page 19 for details.
→Refer to page 15 for details.
A027XB-K71M-P φ28A227XB-K71M-P φ28
A027XB-K71MN-P φ28
A227XB-KB02V-P φ28
A227XB-KB08M-P φ28
A227XB-KB02VN-P φ28
A227XB-KB08MN-P φ28
A227XB-KB02VL-P φ28
A227XB-KB08ML-P φ28
Pushbutton switch type
Touch type Special
Lever switch type Photoelectric typeRe�ection type (downward) Transmission type
◇ 7-segment indication [one digit] ◇ 7-segment indication [one digit]
◇ 7-segment indication [one digit] ◇ 7-segment indication [one digit]
A227XB-K71MN-P φ28
A227XB-73M2-P φ28 1 2 A027XB-73MN-P φ28 1 2
A227XB-73MN-P φ28 1 2
◇ 7-segment indication [three digits] ◇ 7-segment indication [three digits]
→Refer to page20 for details.
→Refer to page21 for details.
LED indicationonly
Stationarytype (Green)
*Indication only (no response)
Model of A027XB-02GN2-P is classified as A0:27:XB-: :02:G:N:2:-P, and can be used as a reference for confirmation of the specifications.
AnyWire transmission method
Number of occupied points/number of 7-segment digits
LED indicationAddress settingmethod
A0: Bitty typeA2: DB A20 type
Shape/structureNo mark: Standard typeK: Standard compactE: Dust-proof typeF: Door opening/closing type
-02: 2 points including input and output*There are some points according to the number of points.-71: 7-segment one digit-73: 7-segent three digits
G: Green (mono-color)V: Selection of one color from seven colorsM: RGB independent ON/OFF
Response methodNo mark: Lever switchN: Pushbutton switchL: Photoelectric downward re�ection
2: DIP switch3: Address writer*Omitted because all are 3 for standard compact
◆ Model *The following is a simpli�ed description. Keep this in mind as a reference because there are some exceptions.
List of POKAYOKE terminal productsS
elec
tion
type
Sel
ectio
n of
on
e co
lor
from
se
ven
colo
rs
Comb
inatio
n typ
eRG
B ea
ch c
olor
Ind
epen
den
t O
N/O
FF
Do
or
open
ing/c
losing
+ L
ED in
dicat
ion
7-se
gm
ent
ind
icat
ion
+ L
ED
ind
icat
ion
Buz
zer
+ LE
D in
dica
tion
Stat
iona
ryty
pe (G
reen
)
Sel
ectio
n ty
peS
elec
tion
of
one
colo
r fr
om
seve
n co
lors
Selec
tion t
ype
Selec
tion
of
one
colo
r fro
m
seve
n co
lors
Co
mb
inat
ion
typ
eR
GB
eac
h co
lor
Ind
epen
den
t O
N/O
FF
Comb
inatio
n typ
eRG
B each
color
Indep
ende
nt
ON/O
FF
One digit
Three digits
1 2
1 2
1 2
1 2
Double-sided
tape
*Speci�cations of each modelare indicated by icon.
◆ Installation method
M3 screwM3
M4 screwM4
Double-sided tapeDouble-sided
tape
φ28 pipeφ28
Address writer
DIP switch1 2
◆ Address setting method
AnyWire Bitty
AnyWire DB A20
◆ AnyWire transmission method
Green
◆The color of LED indication
“Selection type”: The indication color of this terminal can be selected from seven colors.“Combination type”: The indication color of this terminal can be set from 7 kinds of color by a combination of RGB.
Red
Blue
Yellow*
Sky blue
Purple
White
*The actual color is close to orange
VariationsPOKAYOKE Terminal series
POKAYOKE Terminal series11
POKAYOKE Terminal series
POKAYOKE Terminal seriesProducts
12
Indication: LED (stationary, selection, combination) Response: Lever switch
*Products marked with ∆ are made-to-order.
◆Address writerOpenARW-04Non-
contact typeAddress writer (general-purpose)
OpenARW-04-RHNon-contact typeAddress writer ARW-04 + Infrared ray remote head
OpenARW-RHNon-contact typeInfrared ray remote head for address writer
◆ LED indication: Stationery type Lever switch type
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
A027XB-K02V-P φ28 pipe
φ28 pipe
φ28 pipe
φ28 pipe
121 1
A027XB-K06M-P121 3
φ28 pipe
φ28 pipe
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
A227XB-K02V-P121 1
A227XB-K06M-P121 3
20
20
20
20
20
1 1
1 1
1 1
1 1
1 3
Bitty
Bitty
DB A20
DB A20
Bitty
Bitty
BittyDB A20
Bitty
Lever switch
Lever switch
Lever switch
Lever switch
Lever switch
Lever switch
A027XB-02G2-P
A027XB-E02G3-P
A027XB-02G3-P
A027XB-06M2-P
A227XB-02G2-P
One colorselection type
20
Page of dimensionaloutlinesdrawing
◆ LED indication: Selection type Lever switch type
◆ LED indication: Combination type Lever switch type
◆ Option
27
27
27
27
27
27
27
27
27
27
30
-
-
1 1 DB A20 A227XB-02G3-P
A027-HP28-5P φ28 pipe[H] holder φ28 pipe installation holder lower tightening type (including 5 holders)
A027-HP28-H1-5P φ28 pipe[H1] holder
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
A027-HP-SUS2SUS pipe[SUS] holder
Standard price (¥)Product speci�cations ModelInstallation
Open
Open
Open
Open
Page ofdimensionaloutlines drawing
30
30
Slide
Slide
-
-
30
-Terminal A027-LES-01-5PReplacement rubber lever set (including cover, lever, ring respectively 5 pieces)
A027-KA2-5PAddress switch cover (slide type, transparent) (including 5 pieces)
A027-KA3-5PAddress switch cover (slide type, Black) (including 5 pieces)
Open
Open
・Common
・For standard type
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
L E DStationary type (Green)
L E D
L E D
L E D
L E D
1 2
1 2
1 2
Standardprice (¥)
DIP switch Address writer1 2
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
L E DCombinationtype
L E D
L E D
Standard type Standard compact type
A□27XB-0□□2-PA□27XB-0□□3-PA027XB-E02G3-P
A□27XB-K02V-PA□27XB-K06M-P
Lever switchStationary type (Green)
Lever switchStationary type (Green)
Lever switchStationary type (Green)
Lever switchStationary type (Green)
φ28 pipe
φ28 pipe
φ28 pipe
φ28 pipe
One colorselection type
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Combinationtype
Combinationtype
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
ProductsPOKAYOKE Terminal series
POKAYOKE Terminal series13
Indication: LED (stationary, selection, combination) Response: Pushbutton switch
*Products marked with ∆ are made-to-order.
◆ LED indication: Stationery type Pushbutton switch type
◆ LED indication: Selection type Pushbutton switch type
◆ LED indication: Combination type Pushbutton switch type
A027XB-K02VN-P φ28 pipe
φ28 pipe
φ28 pipe
φ28 pipe
121 1
A027XB-K06MN-P121 3
φ28 pipe
φ28 pipe
φ28 pipe
Open
Open
Open
Open
Open
Open
A227XB-K02VN-P121 1
A227XB-K06MN-P121 3
20
20
20
1 1
1 1
1 1
Bitty
Bitty
DB A20
DB A20
Bitty
BittyDB A20
Pushbutton
Pushbutton
Pushbutton
Pushbutton
Pushbutton
Pushbutton
Pushbutton
A027XB-02GN2-P
A027XB-02GN3-P
A227XB-02GN2-P φ28 pipe201 1 DB A20 A227XB-02GN3-P
27
27
27
27
27
27
27
27Pushbutton
L E DStationary type (Green)
L E DStationary type (Green)
L E DStationary type (Green)
L E DStationary type (Green)
1 2
1 2
L E DCombinationtype
L E DCombinationtype
One colorselection type
One colorselection type
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
Standard type Standard compact type
A□27XB-02GN2-PA□27XB-02GN3-P
A□27XB-K02VN-PA□27XB-K06MN-P
OpenARW-04
OpenARW-04-RHOpenARW-RH
◆ Option
30
-
-
A027-HP28-5P
A027-HP28-H1-5P
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
A027-HP-SUS2
Open
Open
30
30
-
-
30
A027-KA2-5P
A027-KA3-5POpen
Open
・Common
・For standard type
Open
Open
Open
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
◆Address writerNon-
contact typeAddress writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
Slide
Slide
Address switch cover (slide type, transparent) (including 5 pieces)
Address switch cover (slide type, Black) (including 5 pieces)
[H] holder φ28 pipe installation holder lower tightening type (including 5 holders)
[H1] holder
[SUS] holder
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
φ28 pipe
φ28 pipe
SUS pipe
POKAYOKE Terminal series
POKAYOKE Terminal seriesProducts
14
Indication: LED (stationary) Detection: Photoelectric downward reflection type
*Products marked with ∆ are made-to-order.
・For standard type
・Common
◆ LED indication: Stationery type Photoelectric downward re�ection
標準価格(¥)標準価格(¥)27
27
27
27
φ28 pipe
φ28 pipe
φ28 pipe
Open35
35
35
35
1 1
1 1
1 1
Bitty
BittyDB A20
Downwardreflection A027XB-02GL2-P
A027XB-02GL3-P
A227XB-02GL2-P φ28 pipe1 1 DB A20 A227XB-02GL3-P
L E DStationary type (Green)
L E DStationary type (Green)
L E DStationary type (Green)
L E DStationary type (Green)
1 2
1 2
A□27XB-02GL2-PA□27XB-02GL3-P
Standard type
OpenARW-04
OpenARW-04-RHOpenARW-RH
◆ Option
30
-
-
A027-HP28-5P
A027-HP28-H1-5P
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
A027-HP-SUS2
Open
Open
30
30
-
-
30
A027-KA2-5P
A027-KA3-5POpen
Open
Open
Open
Open
Open
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Downwardreflection
Downwardreflection
Downwardreflection
◆Address writerNon-
contact typeAddress writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
Slide
Slide
Address switch cover (slide type, transparent) (including 5 pieces)
Address switch cover (slide type, Black) (including 5 pieces)
[H] holder φ28 pipe installation holder lower tightening type (including 5 holders)
[H1] holder
[SUS] holder
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
φ28 pipe
φ28 pipe
SUS pipe
ProductsPOKAYOKE Terminal series
POKAYOKE Terminal series15
Indication: LED (stationary) Detection: Photoelectric transmission type
*Products marked with ∆ are made-to-order.
◆ LED indication: Stationery type Photoelectric transmission type
A027-TPCM3 screw
M3 screw
M3 screw
Protective bracket for transmission type terminal(including 1 piece)
A027-THP28-H1 φ28 pipe
A027-TS-5PInstallation screw set for transmission type terminal (for product with no protective bracket) (including 5 pieces)
A027-TPS-5PInstallation screw set for transmission type terminal (for product with protective bracket) (including 5 pieces)
21
25
1
1
1 1
Bitty
Bitty
DB A20
A027PB-T14P02D-P
A027XB-T14P02D-C
21
25
21
25
21
25
1
1 1
Bitty
Bitty
A027PB-T07P02D-P
A027XB-T07P02D-C
A227PB-T14P02D-P
A227XB-T14P02D-C
A227PB-T07P02D-P
A227XB-T07P02D-C
Lightaxis
3
3
M3 screw
M3 screw
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
Open
21
25
1
1 1
Bitty
Bitty
Transmission (light emission)Transmission (light reception)
A027PB-T02G-P
A027XB-T02G-C
3
3
3
3
3
3
5
5
5
5
M3 screw
M3 screw
21
25
1
1 1
A227PB-T02G-P
A227XB-T02G-C
1 1
1
1 1
DB A20
DB A20
DB A20
DB A20
DB A20
*Consuming current (mA) in combination of light emission and light reception ex. For “A027PB-T02G-P” and “A027XB-T02G-C” → (40mA × [number of set units]) + 150mA
A027-T07PCM4 screw
M4 screw
M4 screw
M4 screw
Protective bracket for transmission type terminal (Dust-proof: 70mm) (including 1 piece)
A027-TPSM4-5P φ28 pipe
φ28 pipe
φ28 pipe installation holder for transmission type terminal (Dust-proof: 70mm) (including 1 piece)φ28 pipe installation holder for transmission type terminal (Dust-proof: 140mm) (including 1 piece)
A027-T14PCProtective bracket for transmission type terminal (Dust-proof: 140mm) (including 1 piece)
A027-TSM4-5PInstallation screw set for transmission type terminal(for product with no protective bracket) (including 5 pieces)Installation screw set for transmission type terminal(for product with protective bracket) (including 5 pieces)
A027-T07PHP28-H1
-
A027-T14PHP28-H1
FK4-P075-1004-core flat cable (oil resistance) (AWG18 (0.75sq) × 4-core Insulation sheath outer diameter φ2.5±0.1mm)
Maximumdetectiondistance(mm)
M4 screw
M4 screw
M4 screw
M4 screw
M4 screw
M4 screw
M4 screw
M4 screw
1200
1200
1200
1200
300
300
300
300
1000
1000
1000
1000
28
28
28
28
-
-
-
27
27
-
-
27
27
27
27
28
28
28
28
28
28
28
28
L E DStationary type (Green)
L E DStationary type (Green)
L E DStationary type (Green)
L E DStationary type (Green)
L E DStationary type (orange)
L E D
L E D
L E D
L E D
L E D
L E D
L E D
◆ LED indication: Stationery type Photoelectric transmission type (Dust-proof: 70mm short)
・Option
・Option
◆ LED indication: Stationery type Photoelectric transmission type (Dust-proof: 140mm long)
*Consuming current (mA) in combination of light emission and light reception ex. For “A027PB-T07P02D-P” and “A027XB-T07P02D-C” → (40mA × [number of set units]) + 150mA
◆Address writerOpenARW-04
OpenARW-04-RHOpenARW-RH
30
-
-
Open
Open
Open
Open
Open
Open
φ28 pipe installation holder for transmission type terminal
Transmission (light emission)Transmission (light reception)
Transmission (light emission)Transmission (light reception)Transmission (light emission)Transmission (light reception)
Lightaxis
Maximumdetectiondistance(mm)
Stationary type (orange)
Stationary type (orange)
Stationary type (orange)
Stationary type (orange)Transmission (light emission)Transmission (light reception)Transmission (light emission)Transmission (light reception)
Stationary type (orange)
Stationary type (orange)
Stationary type (orange)
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Standard price (¥)Product speci¡cations ModelInstallationPage of
dimensionaloutlines drawing
Standard price (¥)Product speci¡cations ModelInstallationPage of
dimensionaloutlines drawing
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Non-contact typeAddress writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci¡cations ModelTypePage of
dimensionaloutlines drawing
1 2
1 2
1 2
1 2
POKAYOKE Terminal series
POKAYOKE Terminal seriesProducts
16
Instruction: Door opening/closing + LED (Stationary) Response: Lever switch type
*Products marked with ∆ are made-to-order.
28Standby 19Motion 522 φ28 pipe Open1 1 BittyLever switch A027XB-F02G3-P
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
□Arm vertical motion angle □Arm lowering delay time
28 φ28 pipe Open1 1 DB A20Lever switch A227XB-F02G3-P
◆Door opening/closing + LED indication: Stationary type Lever switch type LED+
stationary type(Green)
Door
◆Address writer
OpenARW-04
OpenARW-04-RHOpenARW-RH
◆ Option
30
-
-
A027-HP28-5P
A027-HP28-H1-5P
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
A027-HP-SUS2
Open
Open
Open
30
30
-
-
30
- A027-LES-01-5P
A027-KA2-5P
A027-KA3-5POpen
Open
・Common
30 OpenARW-02V1Address writer (Door opening/closing POKAYOKE recommended)
Open
012345678910
0.712345678910
Set value Delay time (Second)
ARW-02V1 ARW-04
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
LED+stationary type(Green)
Door Standby 19Motion 522
“Address,” “Door arm raising and lowering angle” and “door arm lowering motion delay time” can be set by address writer.*“Door arm raising and lowering motion speed setting” cannot be performed.
Arm vertical motion angle can be set at seven stages up to approximately 180°. Adjustment can be made when the door collides with the shelf or work.Write No. of approximate position where you want to stop the door in angle setting mode of the address writer.*The angle is an approximate one, and the angle cannot be strictly designated.
When the unloading indication lamp is lit (output is turned ON), the arm is raised in conjunction with the lamp, and when the lamp is unlit (output is turned OFF), the arm is automatically lowered after a certain time.This delay time until the arm is lowered can be set at 11 stages.
Non-contact type
Non-contact type
Address writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
φ28 pipe[H] holder φ28 pipe installation holder lower tightening type (including 5 holders)
φ28 pipe[H1] holder
SUS pipe[SUS] holder
TerminalReplacement rubber lever set (including cover, lever, ring respectively 5 pieces)
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
Slide
Slide
Address switch cover (slide type, transparent) (including 5 pieces)
Address switch cover (slide type, Black) (including 5 pieces)
0°About 25°
About 45°
About 73°
About 90°
About 130°About 155°About 180°
ProductsPOKAYOKE Terminal series
POKAYOKE Terminal series17
Indication: 7-segment + LED (selection, combination) Response: Lever switch type
*Products marked with ∆ are made-to-order.
◆ 7-segment + LED indication: Selection type Lever switch type
◆ 7-segment + LED indication: Combination type Lever switch type
28
28
28
28
29
φ28 pipe
φ28 pipe
φ28 pipe
φ28 pipe
φ28 pipe
Open
Open
Open
Open
Open
A027XB-K71V-P181 5
A227XB-K71M-P181 7
A027XB-K71M-P181 7
A227XB-K71V-P18
20
1 5
1 16
BittyDB A20
BittyDB A20
DB A20
Lever switch
Lever switch
A227XB-73M2-PLever switch
Lever switch
Lever switch
LED+
7-segment+one colorselection type
+
LED+
LED+
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
Standard type Standard compact typeA227XB-73M2-P
A□27XB-K71V-PA□27XB-K71M-P
1 2
OpenARW-04
OpenARW-04-RHOpenARW-RH
30
-
-
A027-HP28-5P
A027-HP28-H1-5P
A027-HP-SUS2
Open
Open
Open
30
30
-
-
30
- A027-LES-01-5P
A027-KA2-5P
A027-KA3-5POpen
Open
Open
7-segment
7-segment
7-segment
7-segment
one colorselection type
One digit
One digit
One digit
One digit
Three digits
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Combinationtype
Combinationtype
Combinationtype
◆Address writerNon-
contact typeAddress writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
Slide
Slide
Address switch cover (slide type, transparent) (including 5 pieces)
Address switch cover (slide type, Black) (including 5 pieces)
・For standard type Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
◆ Option φ28 pipe[H] holder φ28 pipe installation holder lower tightening
type (including 5 holders)
φ28 pipe[H1] holder
SUS pipe[SUS] holder
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
TerminalReplacement rubber lever set (including cover, lever, ring respectively 5 pieces)
・Common
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
POKAYOKE Terminal series
POKAYOKE Terminal seriesProducts
18*Products marked with ∆ are made-to-order.
40,000
29
29
29
29
29
29
φ28 pipe
φ28 pipe
φ28 pipe
φ28 pipe
φ28 pipe
Open
A027XB-K71VN-P181 5
A227XB-K71MN-P181 7
A027XB-K71MN-P181 7
A227XB-K71VN-P18
20
1 5
1 16
BittyDB A20
Bitty
Bitty
DB A20
A027XB-73MN-P φ28 pipe201 16 DB A20 A227XB-73MN-P
◆ 7-segment + LED indication: Selection type Pushbutton switch type
◆ 7-segment + LED indication: Combination type Pushbutton switch type
Open
Open
OpenLED+
LED+
+
+
LED+
LED+
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
Standard type Standard compact type
A027XB-73MN-PA227XB-73MN-P
A□27XB-K71VN-PA□27XB-K71MN-P
Pushbutton
Pushbutton
Pushbutton
Pushbutton
Pushbutton
Pushbutton
1 2
1 2
OpenARW-04
OpenARW-04-RHOpenARW-RH
30
-
-
A027-HP28-5P
A027-HP28-H1-5P
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
A027-HP-SUS2
Open
Open
30
30
-
-
30
A027-KA2-5P
A027-KA3-5POpen
Open
Open
Open
Open
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Combinationtype
Combinationtype
Combinationtype
Combinationtype
◆Address writerNon-
contact typeAddress writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
Address switch cover (slide type, transparent) (including 5 pieces)
Address switch cover (slide type, Black) (including 5 pieces)
・For standard type Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
◆ Option φ28 pipe[H] holder φ28 pipe installation holder lower tightening
type (including 5 holders)
φ28 pipe[H1] holder
SUS pipe[SUS] holder
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing・Common
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
Indication: 7-segment + LED (selection, combination) Response: Pushbutton switch
Slide
Slide
7-segment one color
selection type
7-segment one color
selection type
7-segment
7-segment
7-segment
7-segment
One digit
One digit
One digit
One digit
Three digits
Three digits
ProductsPOKAYOKE Terminal series
POKAYOKE Terminal series19
Instruction: Buzzer + LED (selection, combination)
Response: Lever switch type, pushbutton type, photoelectric downward reflection type
*Products marked with ∆ are made-to-order.
◆ Buzzer + LED indication: Selection type, combination type Lever switch type
◆ Buzzer + LED indication: Selection type, combination type Photoelectric downward re�ection
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
OpenARW-04
OpenARW-04-RHOpenARW-RH
30
-
-
A027-HP28-5P
A027-HP28-H1-5P
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
A027-HP-SUS2
Open
Open
Open
30
30
30
-Terminal A027-LES-01-5P・For lever switch type
◆ Buzzer + LED indication: Selection type, combination type Pushbutton switch type
29
29
29
29
29
29
φ28 pipe A227XB-KB02V-P101 1 DB A20 φ28 pipe A227XB-KB08M-P141 4 DB A20Lever switch
Lever switch
φ28 pipe A227XB-KB02VN-P101 1 DB A20 φ28 pipe A227XB-KB08MN-P141 4 DB A20
φ28 pipe A227XB-KB02VL-P101 1 DB A20 φ28 pipe A227XB-KB08ML-P141 4 DB A20
Downwardreflection
Downwardreflection
LED+
+
LED+
+
LED+
+
Pushbutton
Pushbutton
Open
Open
Open
Open
Open
Open
Open
Pushbutton switch typeStandard compact type
A227XB-KB02VN-PA227XB-KB08MN-P
Photoelectric downwardreflection typeStandard compact type
A227XB-KB02VL-PA227XB-KB08ML-P
Lever switch typeStandard compact type
A227XB-KB02V-PA227XB-KB08M-P
Buzzer one colorselection type
Buzzer
Buzzer
Buzzer
one colorselection type
Buzzer
Buzzer
one colorselection type
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Combinationtype
Combinationtype
Combinationtype
◆Address writerNon-
contact typeAddress writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
Replacement rubber lever set (including cover, lever, ring respectively 5 pieces)
◆ Option Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
φ28 pipe[H] holderφ28 pipe installation holder lower tightening type (including 5 holders)
φ28 pipe[H1] holder
SUS pipe[SUS] holder
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
・Common
POKAYOKE Terminal series
POKAYOKE Terminal seriesProducts
20
Indication: LED (stationary) Detection: Touch type (photoelectric reflection type)
*Products marked with ∆ are made-to-order.
◆ Option
◆ LED indication: Stationery type Touch type (photoelectric re�ection type) 29
29
30
30
30
30
A092-DMWiringmoldingWiring duct (1m)
A092-CND-05Cable with connectors on both ends (0.3sq × 2-core 5cm)
A092-CND-10Cable with connectors on both ends (0.3sq × 2-core 10cm)
A092-CND-15Cable with connectors on both ends (0.3sq × 2-core 15cm)
A092-CND-20Cable with connectors on both ends (0.3sq × 2-core 20cm)
Double-sidedtape141 1 BittyTouch A092XB-02GL
15㎜
L E DStationary type (Green)
◆Address writerOpenARW-04
OpenARW-04-RHOpenARW-RH
30
-
-
Open
Open
Open
Open
Open
Open
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
This is best suited for the POKAYOKE terminal when
there are many small openings installed on shelves for
small parts and electronic components, etc.
This can be installed if the thickness of the shelf plate,
etc., is 15mm or more. Therefore, it is commonly used in
many situations. This indicates with green LED, and the
input method is a touch type (photoelectric reflection
type). This reacts only by tapping the body by hand.
Because there are no movable parts, it is a hard-to-break
structure.
The POKAYOKE module of the same shape has a wire duct width of 15mm. This can be installed on the side of a shelf plate of which the thickness is 15mm or more, and work time is simplified due to installation only by double-sided tape.
When parts on a shelf where an unloading indication lamp is lit are unloaded and the indication lamp is touched by a finger, “unloading completed” is set.
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
Non-contact typeAddress writer (general-purpose)
Non-contact typeAddress writer ARW-04 + Infrared ray remote head
Non-contact typeInfrared ray remote head for address writer
Standard price (¥)Product speci�cations ModelTypePage of
dimensionaloutlines drawing
WiringmoldingWiring
moldingWiring
moldingWiring
molding
ProductsPOKAYOKE Terminal series
POKAYOKE Terminal series21
Indication: LED (stationary) Response: None
*Products marked with ∆ are made-to-order.
φ28 pipe
φ28 pipe
Open
Open
20
20
1
1
BittyNone A027PB-01G-P
A227PB-01G-PNone DB A2030
30
*The above models are equipped with “H” holder as a standard.*When installing “H1” holder, add “-H1” at the end of the standard model.*When installing “SUS” holder, change the end of the standard model from “-P” to “-PS.”
◆ LED indication: Stationery type Special type (No response)
1 2
1 2
◆ OptionA027-HP28-5P
A027-HP28-H1-5P
*φ28 pipe installation holder is included with the POKAYOKE terminal (φ28 pipe installation type). Single part is an option for change of installation and repair.
A027-HP-SUS2
Open
Open
Open
30
30
-
-
30A027-KA2-5P
A027-KA3-5POpen
Open
・Common
L E DStationary type (Green)
L E DStationary type (Green)
A027PB-01G-PA227PB-01G-P
Standard type
Indication, instruction
Consumptioncurrent
(mA)
TransmissionmethodInstallation Setting
Number ofI/O points
Input Output Model
Response, detection
Page of dimensionaloutlinesdrawing
Standardprice (¥)
DIP switch Address writer1 2
Standard price (¥)Product speci�cations ModelInstallationPage of
dimensionaloutlines drawing
[H] holder φ28 pipe installation holder lower tightening type (including 5 holders)
[H1] holder
[SUS] holder
φ28 pipe installation holder back tightening type (including 5 holders)
SUS pipe installation holder (including 1 holder)
φ28 pipe
φ28 pipe
SUS pipe
Slide
Slide
Address switch cover (slide type, transparent) (including 5 pieces)
Address switch cover (slide type, Black) (including 5 pieces)
POKAYOKE Terminal series
POKAYOKE Terminal seriesProducts
22
Accessories
*Products marked with ∆ are made-to-order.
◆AnyWire Cable/Connector (AnyWire transmission cable & connector)
◇Flat cable appearance photo
LP connector (10 connectors included)
*Crimp type link connector (Allowable current 5A)
Open
Open
Open
Crimping tool for LP connector
FK4-125-100Flat cable (100m winding)(Conductor resistance 0.027Ω/m·Allowable current 5A)
Standard price (¥)Product speci�cations ModelDetails
For 4-core �at cable (0.75sq) (coating outer diameter φ2.54mm Cover: Black Body:Black)
For cabtire cable (Coating outer diameter φ2.1 to 2.4mm Cover: Orange Body: Black)
For cabtire cable (Coating outer diameter φ1.8 to 2.1mm Cover: Yellow Body: Black)
LP4-BK-10P
OpenFor 4-core �at cable (1.25sq) (coating outer diameter φ2.54mm Cover: White Body: Red) Pin protector type LP4-WR-10P
LP4-OR-10P
OpenFor cabtire cable (Coating outer diameter φ1.1 to 1.4mm Cover: White Body: White) LP4-WW-10P
LP4-YE-10P
Open
Open
For 4-core �at cable (0.75sq) (coating outer diameter φ2.54mm Cover: White Body: Black) Pin protector type LP4-WH-10P
Open
OpenFor cabtire cable (Coating outer diameter φ2.1 to 2.4mm Cover: Orange Body: Gray)
For cabtire cable (Coating outer diameter φ1.8 to 2.1mm Cover: Yellow Body: Gray)
LP4-ORG-10P
LP4-YEG-10P
OpenCrimping tool dedicated to LP connector (The connector can be crimped by pliers, etc., however, a dedicated tool is recommended) LP-TOOL
Body colorRed: for wire diameter size 1.25sqBlack: for wire diameter size 0.75sqGray: for wire diameter size 0.5sqWhite: for wire diameter size 0.3sq
4-p
ole
4-core �at cable (AWG16 (1.25sq) × 4-core Insulating coating outer diameter φ2.5±0.1mm)
FK4-075-100 Open4-core �at cable (AWG18 (0.75sq) × 4-core Insulating coating outer diameter φ2.5±0.1mm)
4-core �at cableAWG16 (1.25sq)×4-core
(DN:DP:0V:24V from the left)
4-core �at cableAWG18 (0.75sq)×4-core
(DN:DP:0V:24V from the left)
When using in combination with the dedicated �at cable and LP connector (link connector), connect wires so that the black electric wire (DN line) is on the hinge side (No. 1) of the connector body as shown in the photo.
ProductsPOKAYOKE Terminal series
POKAYOKE Terminal series23
Master Units
*Products marked with ∆ are made-to-order.
◆PLC Interface
◆Touch Panel Interface
◆PC Interface
AFSR01-D2 AFCS01-D2AFCJ01-D2 AF611-D2 AFSP01-D2NP1L-AW1-D2
AFSR01-D2 Open
AFCJ01-D2 Open
AFCS01-D2 Open
AF611-D2 Open
NP1L-AW1-D2 Open
Standardprice (¥)
Model
AFSP01-D2 Open
QJ51AW12D2 Sold byMitsubishi Electric
LJ51AW12D2
FX3U-128BTY-M
QJ51AW12D2
Transmissionmethod
BittyDB A20
DB A20
DB A20
DB A20
DB A20
DB A20
DB A20
DB A20
Master I/F for Yokogawa Electric FA-M3 series 100x29x92.7500512 512
512 512
512 512
512 512
Master I/F for OMRON CJ1 series 65x31x90500Master I/F for OMRON CS1 series 130x34.5x110.5500Master I/F for Toshiba S2T 130x35x113500
512 512Master I/F for Fuji Electric SX 105x34.8x97.3500
*Consumption current is external supply part only. For details, refer to the operation manual.*Master I/F for Sharp JW20/30/300 series, master I/F for Yaskawa Electric MP2000 series also available. For details, contact our sales representative.
Consumptioncurrent
(mA)Product speci�cations Dimensions
(mm)
Support I/O points
Input Output
512 512Master I/F for PANASONIC FPΣ 60x30x90500
APC28-104 Open
AG20-232C Open
AP28-01A Open
AG20-485MD Open
AG20-232C
DB A20
DB A20
DB A20
DB A20
512 512
512 512
512 512
Master I/F for PC104 bus 96x90x15.2500
RS-232C gateway (Note 2) 140x40x60500
*Consumption current is external supply part only. For details, refer to the operation manual.Note 2: Driver development is required because protocol speci�cations differ depending on the connected equipment. For details, contact our sales representative.
Master I/F for PCI bus 150x106.7x21.5500
512 512RS485 Modbus serial I/F 140x40x60500
AFLT01-D2 Open
AFLT01-D2Controller LT3000 series with displayer
DB A20448 448*Consumption current is external supply part only. For details, refer to the operation manual.
Master I/F for digital LT 3000 series 90x71x23.5200
I/F for Mitsubishi Electric MELSEC Q series 98x27.4x90500512 512I/F for Mitsubishi Electric MELSEC L series 90x28.5x95500512 512I/F for Mitsubishi Electric MELSEC F series 90x43x87100128 (Note 1) 128 (Note 1)
Note 1: Number of input points + number of output points ≤ 128 (if number of input points + number of output points ≥ 128, number of input points is prioritized.)
FX3U-128BTY-MLJ51AW12D2
Sold byMitsubishi Electric
Sold byMitsubishi Electric
Standardprice (¥)
ModelTransmissionmethod
Consumptioncurrent
(mA)Product speci�cations Dimensions
(mm)
Support I/O points
Input Output
Standardprice (¥)
ModelTransmissionmethod
Consumptioncurrent
(mA)Product speci�cations Dimensions
(mm)
Support I/O points
Input Output
AP28-01A
POKAYOKE Terminal series
POKAYOKE Terminal seriesProducts
24*Products marked with ∆ are made-to-order.
Master Units
Terminator
Bitty bridge
◆Open FieldBus Gateway
◆Bit dispersion I/O terminal Open Terminal
◆Terminator (Waveform forming module)
◆Bitty bridge (DB A20 - Bitty bridge)
140x57x54.5400256 256
140x57x54.5400512 512
140x57x54.5400512 512
AG22-C1 Open
AG22-D1 Open
NZ2AW1C2D2 Sold byMitsubishi Electric
AG22-C1 AG22-D1NZ2AW1C2D2
Standardprice (¥)Model
NZ2AW1C1BY Sold byMitsubishi
Electric
AB023-D1 Open
AB023-M1 Open
AB023-M2 Open
AB023-D1 AB023-M2AB023-M1NZ2AW1C1BYConsumption
currentProduct specicationsDimensions
(mm)Support I/O pointsInput Output
Connectionspecications
40x100x66 (Excluding
connector part)
Approx. 200mA(When 128 terminalsare connected)(Not includingload current)
Remote device station(1 to 4 stationsare selectable)
256(When 4stations
are occupied)
256
40x100x66Group 2only server
256 256
40x100x73Intelligent I/O 216 216
40x100x66Intelligent I/O 256 256
CC-Link-AnyWire Bitty Bridge unit
for CC-Link ver 1.10
Bit dispersion I/O terminal
for MECHATROLINK-I/II
Bit dispersion I/O terminal
for MECHATROLINK-III
DB A20
DB A20
DB A20
For DB A20 Line terminal, with polarity (attachment holder included) 44x24.5x12Product specications
Dimensions(mm)
Transmissionmethod
AT2 Open
Standardprice (¥)Model
AT0 OpenBitty Line terminal, with polarity (attachment holder included) 44x24.5x12 Bitty
DB A20
Transmissionmethod
Bitty
Bitty
Bitty
Bitty
AnyWire DB A20
Bitty bridgePower combination unit
100x48x40104mA or less(When 128 terminalsare connected)(Not includingload current)
AnyWire DB A20⇔
AnyWire Bitty
256 256 AB07-A-V3 OpenBitty
*Transmission of “Bitty series” can be connected at the lower position of transmission of the “DB A20 series” by using Bitty bridge.
Bit dispersion I/O terminal
for DeviceNet
AT0
Gateway for CC-Link ver 1.10
CC-Link-AnyWire DB A20 Bridge unit for CC-Link ver 2.00
Gateway for DeviceNet
Standardprice (¥)ModelConsumption
currentProduct specicationsDimensions
(mm)Support I/O pointsInput Output
Connectionspecications
Transmissionmethod
(When 4stations
are occupied)Approx. 200mA
(When 128 terminalsare connected)(Not includingload current)
Approx. 200mA(When 128 terminalsare connected)(Not includingload current)
Approx. 200mA(When 128 terminalsare connected)(Not includingload current)
(Excludingconnector part)
Standardprice (¥)
ModelTransmissionmethod
Consumptioncurrent
(mA)Product specications Dimensions
(mm)
Support I/O points
Input Output
Address SettingPOKAYOKE Terminal series
POKAYOKE Terminal series25
Two types of address setting methods
Structure of address
The address of the �rst address is “0.” Then, the address of the next terminal is, as a rule,
“address set value of immediately previous terminal” + “number of occupied points of immediately previous terminal (Number of inputs or outputs, whichever is greater),
ON 1
2
4
8
16
32
64
128
LINK
ADDRESS
ON
Open
DIP switch type
Open the slide coverto set an address
Set an address over the semi-transparent cover
Address writer type
Input 1 point
Output 1 pointInput 1 point
Output 3 point
Input 1 point
Output 7 point
Input 1 point
Output 16 point
Input 1 pointOutput 1 point [Output is common to light
emission and reception]
Number of input and output points
Number of occupied pointsNumber of inputs or outputs,
whichever is greater
Head address setting
1 3 7 16 1
0 1 4 16 * 32
<Example of setting>LINK IN R/W
A027XB-K71MN-P
ADDRESS No.
LINK
128
2
16
6432
84
1
ADDRESSON
MIX TERMINALA227XB-02G2-P
LINK IN R/WA027XB-K02VN-P
248
3216
1
SPDADD
ADDR
ESS
ON
MIX TERMINALA227XB-73MN-P
PIC
KIN
G T
ERM
INAL
A027
PB-T
02G
-P
2841
ON
128643216
ADDR
ESS
PICKIN
G TER
MIN
ALA027XB-T02G
-C
2841
ON
128643216
ADDRESS
*For a terminal of 7-segment 3 digits, address is set in units of 16 points (16 bits). The value is set every 16 points regardless of the number of occupied points of immediately previous terminals.
There are two types of address setting methods for the AnyWire POKAYOKE terminal, and the type depends on the terminal.One is a type to use a DIP switch for setting, and the other is a type to use an address writer to read and write address in a non-contact state.
AnyWire POKAYOKE terminals inform of the existence of terminals to a controller on the upper order by setting the head address of individual terminals. The address is represented by a decimal number, and can be set in units of 1 bit or 16 bits (it differs by product).*Maximum number of points varies with the system configuration. Contact us for details.
Examples of setting in the case that some types of POKAYOKE terminals are combined are shown below.
and values for the number of occupied points are sequentially added. As the number of occupied points differs with each terminal, refer to and confirm by the introduction page of each product. And because the address can be set only in units of 16 points for some terminals, it is necessary to set it to a value larger than the above calculated value and multiples of 16.
It is not necessary that the address set values are in connecting order. If addresses are set without duplication even when the connecting orders are exchanged by remodeling or expansion, operation can be made. And it is not necessary to always set without a margin. If there are number of points to spare and expansion, etc., is expected in the future, skip some addresses when setting.
Unless the address is mistakenly set even if POKAYOKE terminals of two types of address setting methods are combined, it will operate without any problem. However, combining these may result in an address setting error at the time of installation, maintenance or expansion. Therefore, it is not recommended.
“Structure of address” common to all AnyWire POKAYOKE terminals is explained before operation of respective address setting types and setting methods are described.
Address setting by DIP switch
Address setting by address writer
POKAYOKE Terminal series
POKAYOKE Terminal seriesAddress Setting
26
Setting port
■Name of each part
Address writer ARW-04This writer can be used for all POKAYOKE terminals.
ARW-RH
■Reference of approach when address is set and confirmed
When setting an address, be careful of the following.
Address writer ARW-02V1
(Image of operation)
DIP switch type
Address setting
○
○
Setting of door opening/closing type terminal
○*Setting method is described in the manual
◎*Setting method is described on the back of the body
Setting of LED indication (selection type) and buzzer type
○*Setting method is described in the manual
×
Model
ARW-04
ARW-02V1
Operation explanatory diagram on the back of the address writer→
ARW-02V1
Ring for strap POWER indication lampComment indication part
(7-segment 6 digits)
POWER (CLEAR) button
Write button
- Button
Motion button
+ ButtonRead button
Operation modeindication lamp
Light emitting andreceiving position
(upper surface)
Set an address by DIP switch with the slide cover of the POKAYOKE terminal body opened. Be careful of the following points when setting an address.
To set an address by address writer, it is necessary to use an address writer compatible with your POKAYOKE terminal. There are the following two types of address writers.
◇Perform operations of address setting by the address writer with power fed to the POKAYOKE terminal, and reset the power after completion of setting to reflect the setting.
When any change is made in direct mode, the changed content will be immediately reflected.Please keep in mind that when a change is made unexpected movement may occur, and this can be dangerous.
◇Refer to and confirm by the manual for details.
◇Operate the DIP switch with the power for the POKAYOKE terminal turned off.
Change in a power-on state may cause unexpected motion, which is very dangerous.◇Use a non-conductive rod with a thin tip, etc., and make sure to
perform ON/OFF operation of the DIP switch. *There are some products of which the DIP switch is very small and difficult to
operate by finger.
◇Confirm that there is no mixture of foreign matter in the cover after setting, and make sure to completely close the slide cover.
When i t is di f f icul t to hold ARW-04 at narrow locations, use an optional remote head. (Model: ARW-RH)
This address writer is dedicated to the POKAYOKE terminal of door opening/closing type.This is more convenient only for door opening/closing type because indication of motion mode, etc., is suitable for door opening/closing type.
*This can be used for all POKAYOKE terminals if used only for address setting.
*Example: ARW-04 and POKAYOKE terminal o f p h o t o e l e c t r i c transmission type
*Japanese only
ARW-04
Ring for strap
Position of light emitting andreceiving part (yellow part)
POWER indication lamp
Comment indication part (7-segment 6 digits)
RH (Remote head)
Connection connector (Side)
POWER (CLEAR) buttonR button
DOWN button
SELECT button
UP buttonL button
SET button
Operation modeindication lamp
Approx. 20°
Light emittingand receiving part
Setting port
Light emitting and receiving part
Up to approx. 20mm
Setting port
Approx.20°
DimensionsPOKAYOKE Terminal series
POKAYOKE Terminal series27
*Refer to page 30 for dimensional outlines drawings of φ28 pipe installation holder, SUS pipe installation holder and address writer excluding those for transmission type.
Unit: mm
Dimensional outlines drawing
A027-TPC A027-THP28-H1
40
17 41.3
143
130
40
40
2-φ3.5
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
110
55 25 365
1310.2
7.5
30
918
(66)
36
□22
(150)
(48)
φ28
1=DN or G2=DP or D3=0V4=24V
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
A027XB-02G2-PA027XB-02G3-PA027XB-E02G3-PA227XB-02G2-PA227XB-02G3-PA027XB-06M2-P
A027XB-K02V-PA227XB-K02V-PA027XB-K06M-PA227XB-K06M-P
A027XB-K02VN-PA227XB-K02VN-PA027XB-K06MN-PA227XB-K06MN-P
A027XB-02GN2-PA027XB-02GN3-PA227XB-02GN2-PA227XB-02GN3-P
A027PB-T02G-P/A027XB-T02G-CA227PB-T02G-P/A227XB-T02G-C
A027XB-02GL2-P/A027XB-02GL3-PA227XB-02GL2-P/A227XB-02GL3-P
(150)
4=24V3=0V
60
36
2=DP or D1=DN or G
4=24V3=0V2=DP or D1=DN or G
24.1
25 18 (18)
18 9
30
7.5
51.6
66
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
11055
30
(48)
φ28
Hexagon socket head cap screw tightening hole
255 36
1=DN or G2=DP or D3=0V4=24V
918
36
□22
(150)
19
15.5
16
16
4 (Operation stroke: 2.5mm)Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
60
24.136
18 9
3051.6
Hexagon socket head cap screw tightening hole
25 18
4
(18)
(Operation stroke: 3mm)
(150)
UL 202764-core × No.23AWGφ4.6 Gray
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Transmission cable
Light emitting and receiving axis
Light emitting and receiving axis
Take-out check switch (light emitting and receiving part)*Do not dirty.
11055 25 365
(7.5)
30
918
36
□22
Hexagon socket head cap screw tightening hole
(150)
(48)
φ28
1=DN or G2=DP or D3=0V4=24V
HKV4-core × AWG18
13
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
130
130
308130
4
32
4-φ6
45 45
141
(14.5)
11.3
140
130
68
45
20
10
45
95
16.6
0.5
5
5
3
30
13.3
8
9
(7)
140
130
68
45
20
10
45
95
16.6
0.5
5
5
3
30
13.3
8
9
(7)
1=DN or G2=DP or D3=0V4=24V
1=DN or G2=DP or D3=0V4=24V
4-core cabtire cableφ6 0.5mm2
4-core cabtire cableφ6 0.5mm2
Address setting Switch cover
Open state
Address setting Switch cover
Open state
Light emitting side unite
Light receiving side unite
POKAYOKE Terminal seriesDimensions
POKAYOKE Terminal series 28
*Refer to page 30 for dimensional outlines drawings of φ28 pipe installation holder, SUS pipe installation holder and address writer excluding those for transmission type.
Unit: mm
Dimensional outlines drawing
A027PB-T14P02D-P / A027XB-T14P02D-CA227PB-T14P02D-P / A227XB-T14P02D-C
A027PB-T07P02D-P / A027XB-T07P02D-CA227PB-T07P02D-P / A227XB-T07P02D-C
A027-T14PCA027-T07PC
62
47
3
162616
8.41.2
27
15.5
2-R2.25
R1
70
3-φ4
R5.5
56 2828
3
13.513.5
4
8.4
15.5
1.2
132
5-φ6
27
2-R2.25
94
140
R5.5
A027-T07PHP28-H1 A027-T14PHP28-H1
A027XB-F02G3-PA227XB-F02G3-P
73
62
11
33
40.3
2-φ3.5
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
143
132
40
40
11 40.3
33
2-φ3.5
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
18 (18)110
36
365
13
(66)
36
(150)
18 9
Hexagon socket head cap screw tightening hole
30HKV4-core × AWG18
1=DN or G2=DP or D3=0V4=24V (137)
(19.5
)40
M4
tap
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0 A027XB-K71V-P
A227XB-K71V-PA027XB-K71M-PA227XB-K71M-P
(Operation stroke: 3mm)
4
25 18 (18)
(150)
18
36
924.1
UL 202764-core × No.23AWGφ4.6 Gray
51.6
30
60
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
1=DN or G2=DP or D3=0V4=24V
(300)
62 52
70
8
3
2427
R2
3
2427
R2
122
(300)
140
132
(300)
6252
70
8
3
2427
R28
3
2427
R2
122
(300)
140
132
8
1=DN or G2=DP or D3=0V4=24V
1=DN or G2=DP or D3=0V4=24V
Light emitting side unite
Corresponding to the M4 hexagon nut
Corresponding to the M4 hexagon nut
Light receiving side unite
1=DN or G2=DP or D3=0V4=24V
1=DN or G2=DP or D3=0V4=24V
Light emitting side unite
Light receiving side unite
Corresponding to the M4 hexagon nut
Corresponding to the M4 hexagon nut
DimensionsPOKAYOKE Terminal series
POKAYOKE Terminal series29
Dimensional outlines drawing
Unit: mm
*Refer to page 30 for dimensional outlines drawings of φ28 pipe installation holder, SUS pipe installation holder and address writer excluding those for transmission type.
A027XB-73MN-PA227XB-73MN-P
A227XB-KB02V-PA227XB-KB08M-P
A227XB-KB02VL-PA227XB-KB08ML-P
A227XB-KB02VN-PA227XB-KB08MN-P
A092XB-02GL
Hexagon socket head cap screw tightening hole
φ28
1=DN or G2=DP or D3=0V4=24V
HKV4-core × AWG18
362555110
(43)
30
4
36
18 9
(150)Hexagon socket
head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
(Operation stroke: 3mm)
UL 202764-core × No.23AWGφ4.6 Gray
(150) 4
25 18 (18)
18
36
9
24.1
51.6
30
60
Hexagon socket head cap screw tightening hole
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
A027XB-K71VN-PA227XB-K71VN-PA027XB-K71MN-PA227XB-K71MN-P
A227XB-73M2-P
φ28
1=DN or G2=DP or D3=0V4=24V
55110
(43)
36
(66)
3625
10.2
7.5
30
13
918
(150)
Hexagon socket head cap screw tightening hole
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
HKV4-core × AWG18
A092-DM
(150)
60
36
24.1
25 18 (18)
18 9
30
7.5
51,6
66UL 20276
4-core × No.23AWGφ4.6 Gray
1=DN or G2=DP or D3=0V4=24V
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
(150)
60
51.6
36
24.1
(Operation stroke: 3mm)
25
4
18 (18)
18 9
30
UL 202764-core × No.23AWGφ4.6 Gray
1=DN or G2=DP or D3=0V4=24V
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
(150)
60
51.6
36
24.1
(Operation stroke: 3mm)
25
4
18 (18)
18 9
30
15
16,8
UL 202764-core × No.23AWGφ4.6 Gray
1=DN or G2=DP or D3=0V4=24V
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
9
1
9
12
45
2
2
15
Cable duct (cover)
Cable duct (base)
Address writing window and detection window
11
8
15
9
4
1
15
15
11
4
1=DN or G2=DP or D3=0V4=24V
Outline Drawing
POKAYOKE Terminal series
POKAYOKE Terminal seriesDimensions
30
Unit: mm
A092-CND-05A092-CND-10A092-CND-15A092-CND-20
A027PB-01G-PA227PB-01G-P
ARW-02V1ARW-04
19
□22
Hexagon socket head cap screw tightening hole
φ28
1=DN or G2=DP or D3=0V4=24V
HKV4-core × AWG18
36
30
2555110
(48)
36
18 9
(150)Hexagon socket
head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
A027-HP28-5P A027-HP28-H1-5P
A027-HP-SUS2
12.7
518
4.5
2.51.5
15
18 (18)
2
60
36
3040
2-φ4
18
18
1
4
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
40
2-φ
4
M6 �ange nut
60
36
18
418 (32)
Hexagon socket head cap screwM6 × 15 (Included)Tightening torque1.5 ~ 2 N·m
Commercially available round pipeφ28.0
Housing: EHR-2 manufactured by JSTContact: SEH-001T-P0.6 manufactured by JST
100±6
AWG22 UL1007 gray is used
50±6
Housing: EHR-2 manufactured by JSTContact: SEH-001T-P0.6 manufactured by JST
AWG22 UL1007 gray is used
150±6
Housing: EHR-2 manufactured by JSTContact: SEH-001T-P0.6 manufactured by JST
AWG22 UL1007 gray is used
AWG22 UL1007 gray is used
200±6
Housing: EHR-2 manufactured by JSTContact: SEH-001T-P0.6 manufactured by JST
60
36
40
18
(7.3
)7.3
15.3516
2-∅3
.5
M6x25Hexagon socket head cap screw
Dimensional outlines drawing
100
61
100
61 19
iDC Environmental Monitoring Systemcatalog
Price, speci�cations and design may be subject to change without notice.
Mapping catalog
DB A20 series catalog DB A40 series catalog
Energy monitoring energy saving support catalog
Contact
□
□
Contact by mail [email protected]
Contact by website http://www.anywire.jp
POKAYOKE catalog
2016 copyright Anywire Corporation in Japan. October 2016 picpcj-e
<Warranty> <Notes on Safety> ●: WARNING ○: CAUTION◇Warranty period
The warranty on the delivered Product shall continue to be effective for one (1) year after the delivery thereof to a location designated by the original owner.◇Scope of warranty
Should a defect occur in any part of the Product during the foregoing warranty period when it is used normally in accordance with the speci�cations described in this User's Manual, the Company shall replace or repair the defect free of charge, except when it arises as a result of:
(1) Misuse or abuse of the Product by the owner;(2) Fault caused by reason of other than the delivered Product;(3) The unauthorized modi�cation or repair of the Product by any person other than the Company's personnel;(4) Any unusual force of nature, disaster or other cause beyond the Company's control.
The term "warranty," as used herein, refers to the warranty applicable to the delivered product alone. The Company shall not be liable for consequential or incidental damage resulting from any malfunction.◇Repair at cost
After the expiration of the warranty period, the owner shall be responsible for all costs and expenses incurred for the troubleshooting and repair of the Product. Even during the warranty term, the Company shall repair any defects arising from causes other than within the scope of the warranty as speci�ed above, at the owner's cost.
●System Safety- This system is intended for general industrial applications. It does not include functions for supporting applications requiring higher levels of safety such as safety-related devices or accident prevention systems. The product must not be used for these purposes.
- Always turn off the power before attempting to mount or replace.
○System power supplyUse a stable, 24V DC power supply. Use of an unstable power supply may cause problems with the system.
○Separately route high-voltage and power cablesAlthough the system has a high noise margin, separate the transmission line and the input/output cables from the high voltage line and the power line.
○Connector and terminal connection* Pay careful attention to the length and installation of cable wiring to ensure that connectors and cables are neither overloaded nor disconnected.* Make sure to prevent any metal objects from getting inside the connectors or the terminal blocks.* Short-circuits caused by metal objects or mis-wiring are likely to damage the device.
○Do not impose any external loads on the units. Doing so may cause a failure.○Do not disconnect or reconnect between the transmission line and slave units. A malfunction may occur.○Use the POKAYOKE terminal series, DB A20 series, Bitty series within the range of the speci�cations and conditions speci�ed in each manual.
Comments/suggestions about AnyWire products:
ISO9001 / 1400Certi�cation
ISO9001 Applicable scope: Headquarters, East Japan Of�ce, Kyoto FactoryISO14001 Applicable scope: Headquarters, Kyoto Factory
Anywire Corporation
http://www.anywire.jp
□ Headquarters1 Babazusho, Nagaokakyo-shi, Kyoto 617-8550 JAPAN
AnyWireASLINK system catalog
Bitty series catalog
Top Related