memoria de CLCULO
INDICE
1.- ALCANCE.23.- PARAMETROS DE DISEO.24.- MATERIALES55 .- ESTRUCTURACION56.- COMBINACIONES DE CARGA107.- CARGAS:118.- CARGAS PARA SISMO:128.1.- CARGAS DE VIENTO.129.- RESULTADOS DEL ANALISIS:139.1 DESPLAZAMIENTOS LATERALES DE LA ESTRUCTURA. (DISTORSONES)139.2 DEFLEXIONES EN VIGAS Y ARMADURAS1510.- DISEO:1710.1.- REVISION DE MUROS1710.2.- REVISION DE ARMADURAS DE ACERO2510.3.- REVISION DE ZAPATAS.27
1.- ALCANCE.
Se tiene planeado construir un edifico que tendr la funcin de Punto de venta, adems de contar con un rea de atencin y baos.
El edificio ser de un piso.
La presente memoria revisara la cimentacin las columnas y techo para las distintas cargas a las que ser sometida la estructura, como cargas propias, cargas vivas, sismo, viento, cabe comentar que se realiz un estudio de mecnica de suelos, en donde nos indica que tipo de cimentacin recomendada.
2.- REGLAMENTOS PARA ANALISIS Y DISEO. Manual de obras civiles, (CFE). ACI-08, American concrete institute. AISC-10 LRFD, American Institute Steel Construction, por factores de carga. Normas Tcnicas Complementarias 2004 sobre criterios y acciones para el diseo estructural de las edificaciones. (NTCCA-RCDF-2004)
Para el anlisis y diseo de la estructura se emple el software, Ram Elements 10.53.- PARAMETROS DE DISEO.
LOCALIZACION:
La localizacin geogrfica del sitio de estudio se estableci empleando un Sistema dePosicionamiento Global (GPS). Con ello se determin que las coordenadas UTM mediascoincidentes con la posicin del predio corresponden, a las 795005 y 2121888 del Huso14Q.El sitio destinado para el proyecto corresponde al Macrolote 11, con rea cercana a las 12hectreas, ubicado hacia el costado poniente de la zona denominada Centro Comercialdespus del Macrolote 12, as mismo se encuentra ubicado entre las dos vas de ferrocarril
Uso: Comercial
Clasificacin de la estructura segn su importancia: Grupo B.
Factor de comportamiento ssmico: Qx=Qy= 2 Capacidad de carga del terreno: 20 tons/m2
Espectro de Diseo Ssmico:Del estudio de mecnica de suelos:
Del programa prodisis de CFE, tenemos el coeficiente ssmico para el mtodo simplificado.El coeficiente ssmico es de 0.36
Verificacin de requisitos de CFE, para validar que la estructura puede ser revisada con el mtodo de diseo ssmico simplificado del manual CFE:4.- MATERIALES
Concreto en zapatas: fc=250 kg/cm2
Concreto en plantilla: fc=100 kg/cm2
Acero Fy= 2530kg/cm2; FU= 4080 kg/cm2; ASTM-A-36,
Acero Fy= 3515 kg/cm2; FU = 4569.5 kg/cm2 ASTM A-992
5 .- ESTRUCTURACION
La estructura se plante por medio de marcos de concreto y losa de concreto maciza.
6.- COMBINACIONES DE CARGA
Datos de CargasNOMENCLATURA
Comb: Indica si la carga es una combinacin
Estados de carga
EstadoDescripcinComb.CategoraCMCarga MuertaNoDLCVCarga vivaNoLLSXSismo en XNoEQSZSismo en ZNoEQVXViento en XNoWINDVZViento en ZNoWINDD11.4CMSiD21.2CM+1.6CVSiD31.2CM+0.5VXSiD41.2CM+0.5VZSiD51.2CM+VXSiD61.2CM+VZSiD71.2CM+CV+VXSiD81.2CM+CV+VZSiD91.2CM+SXSiD101.2CM+SZSiD111.2CM+CV+SXSiD121.2CM+CV+SZSiD130.9CM+VXSiD140.9CM+VZSiD150.9CM+SXSiD160.9CM+SZSiS1CMSiS2CM+CVSiS3CM+0.75CVSiS4CM+0.6VXSiS5CM+0.6VZSiS6CM+0.7SXSiS7CM+0.7SZSiS8CM+0.525SXSiS9CM+0.525SZSiS100.6CM+0.6VXSiS110.6CM+0.6VZSiS120.6CM+0.7SXSiS130.6CM+0.7SZSiRS11.1CM+1.1CV+SX+0.3SZSiRS21.1CM+1.1CV+0.3SX+SZSiRS31.1CM+1.1CV-SX-0.3SZSiRS41.1CM+1.1CV-SX+0.3SZSiid331.1CM+1.1CV+0.3SX-SZSi
7.- CARGAS:
Carga muerta
Losa . 240 kg/m2Impermeabilizante 10 kg/m2Teja de Barro recocido 50 kg/m2Instalaciones 30 kg/m2TOTAL 330 kg/m2
Ms peso propio de los elementos estructurales, que son considerados automticamente por el programa. Carga viva:
8.- CARGAS PARA SISMO:
AREACM+CV (Kg/m2)PESO (T)H (m)FS (T)
113330.0573.411
8.1.- CARGAS DE VIENTO.
9.- RESULTADOS DEL ANALISIS:
Analysis result
9.1 DESPLAZAMIENTOS LATERALES DE LA ESTRUCTURA. (DISTORSONES)
Current Date: 6/12/2015 11:13 AMUnits system: MetricFile name: C:\Users\baviles\AppData\Roaming\Bentley\Engineering\RAM Elements\RE\Unzipped\PUNTO DE VENTA.etz\
Analysis result
Story drift nodes
Amplification factor::2.00
In XIn ZNodeHTXTXDriftRatioTZTZDriftRatio[m][cm][cm][cm][cm][cm][cm]SX = Sismo en X193.001.591001.591003.182000.010610.000010.000010.000010.00000SZ = Sismo en Z193.000.000000.000000.000010.000001.590991.590993.181980.01061
En este caso tenemos marcos de concreto reforzado que nos limita a 0.012 >0.01061 OK
9.2 DEFLEXIONES EN VIGAS
Current Date: 6/12/2015 11:25 AMUnits system: MetricFile name: C:\Users\baviles\AppData\Roaming\Bentley\Engineering\RAM Elements\RE\Unzipped\PUNTO DE VENTA.etz\
Analysis result
Maximum relative deflectionsRemark.- Magnitude of deflections in absolute value.
CONDITION SS4=CM+WMemberDefl. (2) [cm]@(%)Defl. (3) [cm]@(%)482.33440(L/540)50.000000.00000(< L/10000)100.00000452.33439(L/540)50.000000.00000(< L/10000)100.00000472.33439(L/540)50.000000.00000(< L/10000)100.00000432.33440(L/540)50.000000.00000(< L/10000)100.00000
Podemos apreciar que todas las deflexiones cumplen L/240
10.- DISEO:
10.1.- REVISION DE COLUMNAS
Current Date: 6/12/2015 12:23 PMUnits system: Metric
Design Results
Reinforced Concrete Columns
GENERAL INFORMATION:
Design Code:ACI 318-2011
Load Conditions included in design:D1:1.4CMD2:1.2CM+1.6CVD3:1.2CM+0.8WD4:1.2CM+1.6WD5:1.2CM+CV+1.6WD6:1.2CM+SXD7:1.2CM+SZD8:1.2CM+CV+SXD9:1.2CM+CV+SZD10:0.9CM+1.6WD11:0.9CM+SXD12:0.9CM+SZrs1:1.1CM+1.1CV+1.33SX+1.1SZrs2:1.1CM+1.1CV+1.1SX+1.33SZrs3:1.1CM+1.1CV-1.1SX-1.33SZrs4:1.1CM+1.1CV-1.33SX-1.1SZ
MaterialsConcrete, f'c:0.25 [Ton/cm2]Steel, fy:4.20 [Ton/cm2]Concrete type:NormalSteel, fyt:4.20 [Ton/cm2]Modulus of elasticity:219.36 [Ton/cm2]Type of splices:TangentialUnit weight:2.40 [Ton/m3]Minimum provided Rho:0.010Maximum provided Rho:0.080
General status:OK
COLUMN DATA : 1
GeometrySection type:CircularColumn location:CenterDistance between levels:3.00 [m]Diameter:60.00 [cm]
Rebar
Longitudinal:18-16mmFree cover:2.50 [cm]As provided:36.18 [cm2]Provided Rho:0.013Number of bars:18
Transverse:8 8mm c/ 9.00cm, 9 8mm c/ 19.00cm, 8 8mm c/ 9.00cmInitial spacing (Sini):0.00 [cm]So provided:9.00 [cm]Provided Lo:60.00 [cm]
Design parameters
SlendernessAxis yyAxis xxLu[cm]300.00300.00K3.013.01Pc[Ton]422.16422.16SwayYesYes
Forces
ConditionPositionPuMuxxMuyyVxVyTransverse load[Ton][Ton*m][Ton*m][Ton][Ton]xxyyD1Top-14.94-24.440.000.00-8.15NoNoBottom-17.790.000.000.00-8.15NoNoD2Top-15.06-24.470.000.00-8.16NoNoBottom-17.500.000.000.00-8.16NoNoD3Top-10.56-17.430.000.00-5.81NoNoBottom-13.000.000.000.00-5.81NoNoD4Top-8.31-13.910.000.00-4.64NoNoBottom-10.750.000.000.00-4.64NoNoD5Top-9.72-16.110.000.00-5.37NoNoBottom-12.160.000.000.00-5.37NoNoD6Top-11.26-12.830.000.00-4.34NoNoBottom-13.700.000.000.00-4.34NoNoD7Top-12.81-20.951.62-0.47-6.98NoNoBottom-15.250.000.00-0.47-6.98NoNoD8Top-12.66-14.990.000.00-5.06NoNoBottom-15.100.000.000.00-5.06NoNoD9Top-14.21-23.151.62-0.47-7.72NoNoBottom-16.650.000.00-0.47-7.72NoNoD10Top-5.11-8.680.000.00-2.89NoNoBottom-6.940.000.000.00-2.89NoNoD11Top-8.07-7.680.000.00-2.60NoNoBottom-9.900.000.000.00-2.60NoNoD12Top-9.61-15.711.60-0.48-5.24NoNoBottom-11.440.000.00-0.48-5.24NoNors1Top-11.22-10.811.78-0.53-3.68NoNoBottom-13.460.000.00-0.53-3.68NoNors2Top-11.58-12.682.15-0.64-4.29NoNoBottom-13.820.000.00-0.64-4.29NoNors3Top-14.99-30.57-2.150.61-10.10NoNoBottom-17.230.000.000.61-10.10NoNors4Top-15.35-32.44-1.780.51-10.71NoNoBottom-17.590.000.000.51-10.71NoNoRESULTS OF COLUMN: 1
Column status:OK
Biaxial compression
Controlling condition:rs4Stress in bars:fs>0.5fyDowel splice length:84.00 [cm]Bar clear spacing at splices:5.81 [cm]
ConditionPos.PuMcxxMcyynsxxnsyyCmxxCmyy[Ton][Ton*m][Ton*m]D1Top-14.94-24.440.001.001.000.6000.600Bot.-17.790.000.001.001.000.6000.600D2Top-15.06-24.470.001.001.000.6000.600Bot.-17.500.000.001.001.000.6000.600D3Top-10.56-17.430.001.001.000.6000.600Bot.-13.000.000.001.001.000.6000.600D4Top-8.31-13.910.001.001.000.6000.600Bot.-10.750.000.001.001.000.6000.600D5Top-9.72-16.110.001.001.000.6000.600Bot.-12.160.000.001.001.000.6000.600D6Top-11.26-12.830.001.001.000.6000.600Bot.-13.700.000.001.001.000.6000.600D7Top-12.81-20.951.621.001.000.6000.600Bot.-15.250.000.001.001.000.6000.600D8Top-12.66-14.990.001.001.000.6000.600Bot.-15.100.000.001.001.000.6000.600D9Top-14.21-23.151.621.001.000.6000.600Bot.-16.650.000.001.001.000.6000.600D10Top-5.11-8.680.001.001.000.6000.600Bot.-6.940.000.001.001.000.6000.600D11Top-8.07-7.680.001.001.000.6000.600Bot.-9.900.000.001.001.000.6000.600D12Top-9.61-15.711.601.001.000.6000.600Bot.-11.440.000.001.001.000.6000.600rs1Top-11.22-10.811.781.001.000.6000.600Bot.-13.460.000.001.001.000.6000.600rs2Top-11.58-12.682.151.001.000.6000.600Bot.-13.820.000.001.001.000.6000.600rs3Top-14.99-30.57-2.151.001.000.6000.600Bot.-17.230.000.001.001.000.6000.600rs4Top-15.35-32.44-1.781.001.000.6000.600Bot.-17.590.000.001.001.000.6000.600
ConditionPos.*Mnxx*MnyyMc/(*Mn)Pu/(*Pn)Asreq/AsprovDemand: Capacity Ratio[Ton*m][Ton*m]D1Top-33.660.000.730.040.970.73Bot.34.120.000.000.050.970.05D2Top-33.680.000.730.040.970.73Bot.34.070.000.000.050.970.05D3Top-32.970.000.530.030.970.53Bot.33.350.000.000.030.970.03D4Top-32.560.000.430.020.970.43Bot.33.000.000.000.030.970.03D5Top-32.820.000.490.030.970.49Bot.33.220.000.000.030.970.03D6Top-33.080.000.390.030.970.39Bot.33.470.000.000.040.970.04D7Top-33.112.550.630.030.970.63Bot.33.710.000.000.040.970.04D8Top-33.300.000.450.030.970.45Bot.33.690.000.000.040.970.04D9Top-33.352.340.690.040.970.69Bot.33.940.000.000.040.970.04D10Top-31.960.000.270.010.970.27Bot.32.300.000.000.020.970.02D11Top-32.510.000.240.020.970.24Bot.32.860.000.000.030.970.03D12Top-32.523.310.480.020.970.48Bot.33.100.000.000.030.970.03rs1Top-32.635.370.330.030.970.33Bot.33.430.000.000.030.970.03rs2Top-32.675.540.390.030.970.39Bot.33.480.000.000.040.970.04rs3Top-33.47-2.350.910.040.970.91Bot.34.030.000.000.040.970.04rs4Top-33.57-1.840.970.040.970.97Bot.34.080.000.000.050.970.05
Shear
So provided:9.00 [cm]So calculated:9.60 [cm]Provided Lo:60.00 [cm]Lo calculated:60.00 [cm]S provided:19.00 [cm]S required:19.20 [cm]Sini provided:0.00 [cm]Sini required:4.80 [cm]
Pos.Axis 22Axis 33Mpr [Ton*m]sup. (+)33.6833.66Mpr [Ton*m]sup. (-)33.6833.66Mpr [Ton*m]Bot. (+)34.1234.12Mpr [Ton*m]Bot. (-)34.1234.12Ve [Ton]22.5922.60
ConditionPos.VuVcVs*VnVu/(*Vn)Gob.[Ton][Ton][Ton][Ton]Ve-D10Top31.9624.4622.5335.240.91Bot.31.9624.5722.5335.330.91
Notes
* Torsion is not considered for design.
* Only columns with rectangular or circular sections are designed.
* Each column is verified considering only the forces at the ends of the member.
* The transverse reinforcement is ordered from bottom to top of the column.
* Ve = Design shear force from member moment capacity (2Mp/L). The contribution of the applied gravity shear force is not considered.
* Required So = Maximum spacing between stirrups considering special or intermediate moment frames in the distanced covered by (Lo).
* Calculated Lo = Minimum calculated length measured from joint face along axis of the member, over which transverse reinforcement must be provided with a spacing So. This length is only required for intermediate and special moment frames. ACI 318-11 21.6.4.1
* Lu = Unsupported length.
* K = Effective length factor.
* Cm = A factor relating actual moment diagram to an equivalent uniform moment diagram.
* Sway = True if column is considered unbraced in its local axis.
* Mc = Factored moment to be used for design. Considers the slenderness effects of the column. Mc = Mu*ns.
* n2 = Amplification factor to account for small P-delta effects (P-).
* Mn = Nominal moment strength.
* Mc/(*Mn) = Strength ratio. The bar graphs indicate the relative ratio of Mc/(*Mn) for each load condition. If a bar is shown in red the ratio is greater than one.
10.2.- REVISION DE TRABES DE CONRETO
Current Date: 6/12/2015 12:31 PMUnits system: Metric
Design Results
Reinforced concrete beams
GENERAL INFORMATION:
Design Code:ACI 318-2011
Load conditions included in the design:D1=1.4CMD2=1.2CM+1.6CVD3=1.2CM+0.8WD4=1.2CM+1.6WD5=1.2CM+CV+1.6WD6=1.2CM+SXD7=1.2CM+SZD8=1.2CM+CV+SXD9=1.2CM+CV+SZD10=0.9CM+1.6WD11=0.9CM+SXD12=0.9CM+SZrs1=1.1CM+1.1CV+1.33SX+1.1SZrs2=1.1CM+1.1CV+1.1SX+1.33SZrs3=1.1CM+1.1CV-1.1SX-1.33SZrs4=1.1CM+1.1CV-1.33SX-1.1SZ
Moment frame:Ordinary
MaterialsConcrete, f'c:0.25 [Ton/cm2]Longitudinal reinforcement, fy:4.20 [Ton/cm2]Concrete type:NormalTransversal reinforcement, fyt:4.20 [Ton/cm2]Concrete elasticity modulus:219.36 [Ton/cm2]Steel elasticity modulus:2038.89 [Ton/cm2]Unit weight:2.40 [Ton/m3]Epoxy coated:No
DATA AND RESULTS
Status:OK
Geometry
AxisCol positionBottom widthTop widthDist x[cm][cm][m]1Center60.000.000.002Center60.000.0012.60
SpanDist between axesMember NoSectionbhbwhf[m][cm][cm][cm][cm]1-212.604825.4060.96----
Rebar
Free cover:2.00 [cm]
Longitudinal reinforcementGroupQuantityDiameterPosRef. Axis 1Dist1Ref. Axis 2Dist2Hook1Hook2[m][m]12#6Bottom1-0.2820.28YesYes22#6Top1-0.2820.28YesYes35#6Top1-0.2814.26YesNo45#6Top2-4.2620.28NoYes
Development and splice lengths
GroupDiameterLdLdhSplice L.Total L[cm][cm][cm][m]1#678.0028.00100.0013.682#6100.0028.00130.0013.683#6100.0028.00130.004.804#6100.0028.00130.004.80
Transverse reinforcement
SpanDiameterQuantity@LegsClosed[cm]1-2#34527.002Yes
Initial spacing of stirrups:
SpanInitial SSin lim[cm][cm]0-16.0029.48
FLEXURE
Span: 1-2Member No: 48
Percentage of moment redistributionSupport A = 0.00%Support B = 0.00%Code specified max Rho:maxtop = 1.84%maxbot= 1.84%Limit spacing between bars for cracking control:sb lim = 30.61 [cm]
Positive bending moments
Stationd[cm]Mu[Ton*m]*Mn[Ton*m]Asreq [cm2]Asprov [cm2](%)sb [cm]Mu/(*Mn)No.Dist10%57.050.0011.770.005.680.3913.780.97210%57.052.8511.771.785.680.3913.780.44320%57.058.5711.774.855.680.3913.780.73430%57.0510.9111.775.255.680.3913.780.93540%57.0510.8211.775.205.680.3913.780.92650%57.0510.5011.775.045.680.3913.780.89760%57.0510.8311.775.215.680.3913.780.92870%57.0510.9111.775.255.680.3913.780.93980%57.058.5711.774.855.680.3913.780.731090%57.052.8511.771.785.680.3913.780.4411100%57.050.0011.770.005.680.3913.780.97C0%57.050.0011.770.005.680.3913.780.97
Negative bending moments
Stationd[cm]Mu[Ton*m]*Mn[Ton*m]Asreq [cm2]Asprov [cm2](%)sb [cm]Mu/(*Mn)No.Dist10%55.15-34.65-35.6219.2319.871.423.320.97210%55.15-15.71-35.627.9919.871.423.320.44320%55.15-4.35-35.622.8219.871.423.320.73430%55.150.00-23.530.0012.370.883.320.93540%57.050.00-11.770.005.680.3913.780.92650%57.050.00-11.770.005.680.3913.780.89760%57.050.00-11.770.005.680.3913.780.92870%55.150.00-23.530.0012.370.883.320.93980%55.15-4.35-35.622.8219.871.423.320.731090%55.15-15.71-35.627.9919.871.423.320.4411100%55.15-34.65-35.6219.2319.871.423.320.97C0%55.15-34.65-35.6219.2319.871.423.320.97
SHEAR AND TORSION
Span: 1-2Member No: 48
StationStirrupsSpc provSpc limTu*TnAlVuVsVc*VnVu/(*Vn)No.DistDiamVCT[cm][cm][Ton*m][Ton*m][cm2][Ton][Ton][Ton][Ton]10%#3V27.0027.570.350.440.0016.2612.1811.7517.940.91210%#3V27.0028.530.101.290.0011.0212.6012.1518.560.59320%#3V27.0028.530.061.610.007.1812.6012.1518.560.39430%#327.0028.530.021.610.003.8612.6012.1518.560.21540%#327.0028.530.011.610.002.4512.6012.1518.560.13650%#327.0028.530.001.610.001.7112.6012.1518.560.09760%#327.0028.530.011.610.002.4512.6012.1518.560.13870%#327.0028.530.021.610.003.8612.6012.1518.560.21980%#3V27.0028.530.061.610.007.1712.6012.1518.560.391090%#3V27.0028.530.101.290.0011.0112.6012.1518.560.5911100%#3V27.0027.570.350.440.0016.2612.1811.7517.940.91C0%#3V27.0027.570.350.440.0016.2612.1811.7517.940.91
Notes* Only the design bending forces (Mu), shear forces (Vu) and torsion moments (Tu) are considered in the design.* Values shown in red are not in compliance with a provision of the code* The positive and negative flexural reinforcement includes the longitudinal reinforcement required to resist torsion. Refer to the note below on the VCT column to determine when torsion and compression bars are provided. The longitudinal reinforcement area considers the minimum area required by Code (10.5).* When the moments diagram increases in the same direction of the development length of the bars, the bars will not contribute to the member strength for a Code specified distance equal to max(12*db,d).* If the section at which member flexural strength is being calculated is within the development length of a group of bars, the bars will contribute to the bending capacity an amount proportional to their actual length / their full development length.* The transverse reinforcement is ordered from left to right.* The program does not consider ACI318-11 section 12.11.3 whereby the bar diameter is limited according to the location of the bar cut-off.* Asprov is the provided reinforcement, considering the reduction due to the development length as described previously.* "C" shows the span critical station.* Ld,Ldh = Development length of each bar. If the bar ends with a hook, it considers the Ldh length.* Splice lengths shown are not reduced by the factor Asreq/Asprov.* sb = Free distance between top or bottom bars corresponding to the layer closest to the extreme face of the beam (layer1). It is not calculated when there is only one bar.* Stirrups VCT = Flag that determines if stirrups are required to resist shear forces (V), torsion (T) or to confine the the longitudinal compression bars from buckling (C).* Closed = Flag that indicates if the stirrups are closed (yes) or open (no).* Mu/(*Mn) = Critical strength ratio for the station. If the value is in red, it is larger than 1.0* Al = Total additional longitudinal reinforcement required by torsion.* Spa = stirrup spacing provided by the user.* Spa lim = spacing limits due to geometry. (11.4.5.1, 11.4.5.3, 21.3.4.2, 21.5.3.2)
10.3.- REVISION DE LA LOSA.
Current Date: 6/12/2015 12:46 PMUnits system: MetricFile name: C:\Users\baviles\AppData\Roaming\Bentley\Engineering\RAM Elements\RE\Unzipped\PUNTO DE VENTA.etz\
Analysis result
Plate reinforced concrete design in local axesDesign code: ACI 318-2011Notes:- Membrane forces are ignored in the design- "Bot" is the bottom edge of the plate (-t/2)- "Top" is the top edge of the plate (+t/2)- "ec" is the controlling load condition- Face +t/2 is in compression if bending moments are positive- Large rebar areas (in the order of 1E300) indicate an error in the design due to insufficient thickness of the shell or insufficient strength of the material
Load conditions to be included in design:D1=1.4CMD2=1.2CM+1.6CVD3=1.2CM+0.8WD4=1.2CM+1.6WD5=1.2CM+CV+1.6WD6=1.2CM+SXD7=1.2CM+SZD8=1.2CM+CV+SXD9=1.2CM+CV+SZD10=0.9CM+1.6WD11=0.9CM+SXD12=0.9CM+SZSS1=CMSS2=CM+0.7CVSS3=CM+0.6CVSS4=CM+WSS5=CM+0.6CV+WSS6=CM+SXSS7=CM+SZSS8=CM+0.6CV+SXSS9=CM+0.6CV+SZrs1=1.1CM+1.1CV+1.33SX+1.1SZrs2=1.1CM+1.1CV+1.1SX+1.33SZrs3=1.1CM+1.1CV-1.1SX-1.33SZrs4=1.1CM+1.1CV-1.33SX-1.1SZSDER=CM+CV
SHELL 27Thickness = 10.00 [cm]Mechanical cover = 3.00 [cm]As parallel to 3'As parallel to 1'M11'lcAs3'M33'lcAs1'Node[Ton*m/m][cm2/m][Ton*m/m][cm2/m]25Min.0.10D12Top0.000.03D12Top0.00Max.0.43D8Bot2.500.29rs3Bot1.65FEM: 67Min.0.20D10Top0.000.21D10Top0.00Max.0.59D8Bot3.450.51rs3Bot2.96FEM: 337Min.0.20D10Top0.000.24D10Top0.00Max.0.61D8Bot3.560.66D8Bot3.88FEM: 316Min.0.14D10Top0.000.22D10Top0.00Max.0.51D8Bot2.960.63D8Bot3.73FEM: 304Min.0.23D10Top0.000.23D10Top0.00Max.0.62D8Bot3.560.59rs1Bot3.44FEM: 303Min.0.19D10Top0.000.19D10Top0.00Max.0.57D8Bot3.370.52rs1Bot3.04FEM: 338Min.0.19D10Top0.000.23D10Top0.00Max.0.59D8Bot3.470.64D8Bot3.77FEM: 335Min.0.20D10Top0.000.24D10Top0.00Max.0.62D8Bot3.540.70D8Bot3.11FEM: 336Min.0.23D10Top0.000.25D10Top0.00Max.0.63D8Bot3.580.69D1Bot4.10FEM: 339Min.0.25D10Top0.000.25D10Top0.00Max.0.66D8Bot3.580.67D1Bot3.97FEM: 305Min.0.25D10Top0.000.24D10Top0.00Max.0.64D1Bot3.570.64D1Bot3.45FEM: 66Min.0.23D10Top0.000.23D10Top0.00Max.0.63D8Bot3.500.58D1Bot3.4336Min.0.15D10Top0.000.24D10Top0.00Max.0.52D8Bot3.060.74D8Bot3.3921Min.0.09rs4Top0.000.01rs4Top0.00Max.0.47rs1Bot2.760.40rs1Bot2.34FEM: 317Min.0.16D10Top0.000.21D10Top0.00Max.0.55D8Bot3.230.64rs1Bot3.79FEM: 65Min.0.25D10Top0.000.25D10Top0.00Max.0.64D1Bot3.580.64D1Bot3.7919Min.0.25D10Top0.000.25D10Top0.00Max.0.66D1Bot3.490.66D1Bot3.31
3.58 = 3.55 CM2 QUE CORRESPONDEN A VARILLAS DEL 3 @ 20 CM OK.
10.3.- REVISION DE ZAPATAS.
Current Date: 6/12/2015 1:00 PMUnits system: Metric
Design Results
Reinforced Concrete Footings
GENERAL INFORMATION:
Global status:OKDesign Code:ACI 318-2011Footing type:SpreadColumn type:Concrete
Geometry
Length:1.60 [m]Width:1.60 [m]Thickness:0.55 [m]Base depth:1.25 [m]Base area:2.56 [m2]Footing volume:1.41 [m3]
Column length:61.38 [cm]Column width:61.38 [cm]
Column location relative to footing g.c.:Centered
MaterialsConcrete, f'c:0.25 [Ton/cm2]Steel, fy:4.20 [Ton/cm2]Concrete type:NormalEpoxy coated:NoConcrete elasticity modulus:219.36 [Ton/cm2]Steel elasticity modulus:2038.89 [Ton/cm2]Unit weight:2.40 [Ton/m3]
SoilModulus of subgrade reaction:3150.00 [Ton/m3]Unit weight (wet):1.75 [Ton/m3]
Footing reinforcementFree cover:8.00 [cm]Maximum Rho/Rho balanced ratio:0.75Bottom reinforcement // to L (xx):14-#4 @ 11.00cmBottom reinforcement // to B (zz):14-#4 @ 11.00cm (Zone 1)
Dowel bar sizeRebar 1:8-#6Free cover:2.50 [cm]Development length calculated:compressionBars number // to x axis:3Bars number // to z axis:3Stirrups:#3 @ 20.00cmLegs number // to x axis:2Legs number // to z axis:2
Load conditions to be included in designService loads:SS1:_SS1SS2:_SS2SS3:_SS3SS4:_SS4SS5:_SS5SS6:_SS6SS7:_SS7SS8:_SS8SS9:_SS9SDER:_SDERDesign strength loads:D1:_D1D2:_D2D3:_D3D4:_D4D5:_D5D6:_D6D7:_D7D8:_D8D9:_D9D10:_D10D11:_D11D12:_D12rs1:_rs1rs2:_rs2rs3:_rs3rs4:_rs4
Loads
ConditionFootingNodeAxialMxxMzzVxVz[Ton][Ton*m][Ton*m][Ton][Ton]CM15312.710.000.000.00-5.82CV1531.410.000.000.00-0.73W153-2.810.000.000.001.47SX1530.000.000.000.520.00SZ1531.490.000.000.00-2.59_D115317.800.000.000.00-8.15_D215317.500.000.000.00-8.16_D315313.000.000.000.00-5.81_D415310.750.000.000.00-4.64_D515312.160.000.000.00-5.37_D615315.250.000.000.47-6.99_D715316.800.000.000.00-9.62_D815316.660.000.000.47-7.72_D915318.220.000.000.00-10.36_D101536.940.000.000.00-2.89_D1115311.440.000.000.48-5.24_D1215312.970.000.000.00-7.86_rs115317.230.000.000.61-10.11_rs215317.590.000.000.51-10.71_rs315313.470.000.00-0.53-3.68_rs415313.820.000.00-0.64-4.29_SS115312.710.000.000.00-5.82_SS215313.700.000.000.00-6.33_SS315313.550.000.000.00-6.26_SS41539.900.000.000.00-4.35_SS515310.740.000.000.00-4.79_SS615312.710.000.000.48-5.82_SS715314.250.000.000.00-8.45_SS815313.550.000.000.48-6.26_SS915315.100.000.000.00-8.89_SDER15314.120.000.000.00-6.55
RESULTS:
Status:OK
Soil.Foundation interaction
Allowable stress:2E04 [kg/m2]Min. safety factor for sliding:1.25Min. safety factor for overturning:1.25
Controlling condition:SS9 - 1
ConditionqmeanqmaxmaxArea in compressionOverturningFSFooting[kg/m2][kg/m2][cm][m2](%)FSxFSzslipSS9 - 18.44E031.56E040.4952.561003.541000.001.63
Bending
Factor :0.90Min rebar ratio:0.00200
Development lengthAxisPos.ldlhdDist1Dist2[cm][cm][cm][cm]zzBot.49.5817.3541.3141.31xxBot.49.5817.3541.3141.31
AxisPos.ConditionMu*MnAsreqAsprovAsreq/AsprovMu/(*Mn)Footing[Ton*m][Ton*m][cm2][cm2]zzTopD1 - 10.000.000.000.000.0000.000zzBot.rs2 - 11.4030.9017.6018.060.9740.045xxTopD1 - 10.000.000.000.000.0000.000xxBot.D9 - 12.6730.0317.6018.060.9740.089
Shear
Factor :0.75Shear area (plane zz):0.74 [m2]Shear area (plane xx):0.72 [m2]
PlaneConditionVuVcVu/(*Vn)Footing[Ton][Ton]xyrs2 - 11.0360.500.023yzrs2 - 10.3462.200.007
Punching shear
Perimeter of critical section (b...:4.28 [m]Punching shear area:1.96 [m2]
ColumnConditionVuVcVu/(*Vn)Footing[Ton][Ton]column 1D9 - 110.05328.560.041
Notes
* Soil under the footing is considered elastic and homogeneous. A linear soil pressure variation is assumed.
* The required flexural reinforcement considers at least the minimum reinforcement
* The design bending moment is calculated at the critical sections located at the support faces
* Only rectangular footings with uniform sections and rectangular columns are considered.
* The nominal shear strength is calculated in critical sections located at a distance d from the support face
* The punching shear strength is calculated in a perimetral section located at a distance d/2 from the support faces
* Transverse reinforcement is not considered in footings
* Values shown in red are not in compliance with a provision of the code
*qprom = Mean compression pressure on soil.
*qmax = Maximum compression pressure on soil.
*max = maximum total settlement (considering an elastic soil modeled by the subgrade reaction modulus).
* Mn = Nominal moment strength.
* Mu/(*Mn) = Strength ratio.
* Vn = Nominal shear or punchure force (for footings Vn=Vc).
* Vu/(*Vn) = Shear or punching shear strength ratio.
Page 19 | 29
Top Related