22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
1/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
AIWA
Encender el TV,Abrir el control remoto y buscar las teclas que no tienen acceso para el usuariopresionar una de ellas y
luego DISPLAYaparecerá en la pantalla el menú servicio.Con canal mas-menos seleccionar el ítem.VOLUMEN mas-menos y DISPLAYmuestra los datos a ajustar.Para salir presionar DISPLAY y la otra tecla oculta en el control remoto,aparecerán los caracteres INITIAL porunos segundos y el tv se apagará
BEKO
-Probar con la secuencia Menu y el codigo 9301. o -Probar tambien Menu-Idioma y el codigo 9301.
GRUNDIG
Debereis de probar con estos codigos V+ mas V- mas PR - mas PR +,,,,,8500,,,,,7038,,,,,4934
JVC
Con el televisor conectado presionar: DISPLAY y VIDEO STATUS en el mando a distancia.
En otros modelos:
Presionar SLEEP TIMER en el mando a distancia y ajustar el SLEEP TIMER a 0 minutos.En unos momentossaldra en pantalla la informacion del SLEEP TIMER entonces presionar DISPLAY y VIDEO STATUS] y despuesSERVICE MENU.
Para salir del modo de servicio pulsar exit en el mando a distancia.
LG
En la seccion LG publico varias formas,por lo que tendreis que probar con ellos.
Con el TVC conectado,presionamos a la vez las dos tecla de menu,una esta en el tvc y otra en el mando,conlas teclas channel Up y Down,seleccionamos el ajuste a realizar,y con las teclas volumen Up y Down,le damoslos valores deseados o recomendados por el fabricante.
Simultaneamente pulsar las teclas OK en el mando y el panel del TV.
Desde el control remoto, use la siguiente secuencia 7, 3, 9, 2 ENTER, POWER. Luego SETUP+/-
Encender el tv.pulsar la tecla de menu del panel frontal del tvc y a su vez pulsar la tecla menu del controlremoto, y entraras en le modo servicio.Para navegar por el modo servicio usa las teclas CHANNELUP/DOWN.Para cambiar los datos usa las teclas VOLUMEN UP/DOWN.
Desde el control remoto, presionar la siguiente secuencias de teclas,( 7 - 3 - 9 - 2 - ENTER - POWER ) luegoSETUP +/-OTROS.-Encender el TV, pulsar "menú" en el TV y al mismo tiempo "menu" del mando a distancia. Presionacanal + ó - para selecionar los ítems y volumen + ó - para cambiar los valores.
DAEWOO
Con el televisor funcionando pulsas las teclas de mando a distacia 1 - mute - recall - mute,si no
dispones de la tecla recall tu mando a distancia,entonces utiliza la tecla Display.En algunos modelos noincorporan la tecla recall entonces deberá hacerse la secuencia con display <1 - mute - diplay - mute>
Con el TV apagado, presionar en el control remoto, la siguiente secuencia: DISPLAY,MENU,3,8,POWER, elequipo encendera en modo de servicio. Ingresar a la opcion "Adjustment". Para salir y guardar cambiosapagar el equipo.
FIRST LINE
Desde el control remoto, presionar MENU ingresar a INSTALAR, introducir la secuencia 4, 7, 2, 5. Paraseleccionar los ítem presionar CANAL +/-, para ajustar el valor presionar VOL +/-. Para guardar los cambios
oprimir el botón rojo. Para salir oprimir TV.
En el TV Presionar el botón VOL- , y en el control remoto la secuencia PROG, "-", TV. Para seleccionar losítem presionar CANAL +/-, para ajustar el valor presionar VOL +/-. Para guardar los cambios oprimir el botónrojo. Para salir oprimir TV.
HITACHI
Presionar la tecla "menu" y al mismo tiempo presionar "power".mantenerlos pulsados unos 3 segundospara ajustar los ítems de sonido.Para ajustes de imagen mantener más de 5 segundos.Para poder modificarlos valores se debe colocar D030 para los de video y D020 para los de audio.
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
2/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
KNEISSEL
1º Encender tv y pulsar tecla central de las 5 que tiene el aparato , mantenerla pulsada.2ºApagar de int. general y volverlo a encender,entonces apretar tecla on/off de M/D.3º Con teclas circulares de M/D superior e inferior se ponen los ITEM,con derecha e izquierda se ajustan.4º Los ajustes se memorizan presionando la tecla M amarilla deM/D.
MITSUBISHI
-Existen varios codigos para los televisores de esta marca dependiendo del modelo,aqui teneis alguno deellos,debereis de probar
Pulsar Menu y despues 1257--------- Pulsar menu y despues 1259
Pulsar Menu y despues 1370---------- Pulsar Menu y despues2356Pulsar Menu y despues 2357---------- Pulsar Menu y despues 2358Pulsar Menu y despues 2359
Pulsar Menu y despues 8257
-Con las teclas de video y audio seleccionamos el ajuste que queremos ajustar,y con + o - ajustamos.Paramemorizar tecleamos Enter y despues pulsamos en el menu de pantalla salir del modo de servicio8exitservice mode)
-Desbloqueo de Mitsubishi.Cuando en pantalla aparece "TV Locked", deberemos presionar en el mando adistancia a la misma vez las teclas, simultáneamente las teclas QV (Quick View) y 9. Luego entrar a MENU,buscar la opción: Parental Lock (control de padres),una vez que nos pida la contraseña,volvemos apresionar de nuevo a la misma vez las teclas: QV y 9 y el tvc estara desbloqueado. El código de fabrica es:0000
NOKIA
El Modo de Servicio para el televisor Nokia 21" Mod: 5575 NIC tubo Black Pla y similares es el
siguiente
Pulsar la teclas en el mando a distancia de I(Informacion) M(memoria) y P(tecla de programa)
Desde el control remoto presionar en secuencia los siguientes botones: -/-- , MENU, TV.
PHILIPS
Este modo de servicio para el televisor philips,lo he recogido de foros de lengua inglesa,por eso esta en Ingles.
md1.x Service mode
• To get into service mode short circuit 1s42 and 1s43
• By pressing simultaneously on the keys MENU and - on the TV itself you get into the maintenance menu (SAM).
Service mode 24PW6321/01
ER 0 0 0 0 0 0 0 0 0
E2 Y AX 12 RD 34
U0 N VP 38 GD 28
LL Y VA 00 BD 19
NI Y VL 38 HD 36
TT Y VS 35 HW 40
ET N HP 12
BR Y HG 00
HT 31
Service mode 25PT5121/39
ER 0 0 0 0 0 0 0 0 0
E2 Y AX 13 RD 28
U0 N VP 27 GD 32
LL Y VA 18 BD 40
NI Y VL 31 HD 38
TT Y VS 31 HW 24
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
3/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
ET N HP 36
HG 31
The top line list the last detected errors.
The left row are the options, the two right rows are the geometry settings.
The options are:
E2: 2nd peri
U0: Only UHF
LL: System
NI: NICAM
TT: Teletext France
ET: Teletext Easte
-Cortocircuitar en el tvc los pines M31 y M32,despues debemos de encender el tvc y a realizar los ajustes deseados.En otras versiones dePhilips se puentean los puntos M24 y M25 y por supuesto se enciende el tvc.
-Otra variante de Philips es tirar a masa la patilla N° 1 de la memoria Epron,despues de entrar,para memorizar los ajustes y salir,apagar elaparato con el mando a distancia y despues desconectarlo de la red.
-Estando el tvc funcionando,presionar con el mando a distancia las teclas 062596 y Menu,una vez realizado esto,te saldra la letra S,vuelvea presionar Menu y te saldran los ajustes que quieres realizar,con canal + y - seleccionas y con volumen + y - ajustas,para memorizar ysalir,pulsar Power.
Desbloqueo del modo Hotel.Para salir del Modo Hotel, buscar el programa 38 y pulsar VOL- y STORE durante varios segundos.
PANASONIC
Panasonic tx-28ld2f chasis euro-2
1.Conectas el TV2.Poner en corto temporal el punto de prueba (FA2) y el tv se activara en modo de cambio y las teclas volumen arriba y abajo se ajustanrapidamente3.Oprime al mismo tiempo las teclas del panel del tv ACTION Y VOLUMEN ARRIBA PARA ACTIVAR EL MODO DE SERVICIO
El siguiente modo de servicio lo he sacado de una de las Web de DoubtElectronics,por lo que no estoy completamenteseguro de que sea la forma correcta de entrar,pero si no lo sabemos por intentarlo y comprobar si es valido o no esvalido,no perdemos nada,os pongo la url original,por si quereis comprobarlo por Vds mismos.la direccio es: http://www.calanan.com/panasonic/
Para los televisores Panasonic hay dos formas de entrar en el modo de Servicio.FORMA REMOTA---OTRAS FORMAS.
Forma Remota:A)Con el televisor conectado y con el icono en Setup poner antena en Cable B)Seguidamente con el icono enTimer,poner sleeptimer en 30 c)Salir del menu y ajustar el canal 124,poner el volumen a 0,presionar volumen Down(VD)en el panelfrontal y aparecera CHK en rojo,en la parte superior izquierda de la pantalla,ahora presionas Action y VD en el panel de control y yaestas en el service mode.
Otra Forma:Cortocircuitar el punto de prueba FA1 a FA2,en la chasis TP pin 8 a pin 3,nos aparecera CHK en amarillo en la partesuperior izquierda,seguidamente presionar Action y VD en el panel de contro y CHK cambiara de color a rojo,y ya estamos en elService Mode
Una vez dentro del menu de servicio,tenemos 5 submenus que son:
'B' VCJ Sub Adjustment 'C' W.B. Adjustments 'D' Pincushion Adjustments 'S' Options Adjustments
CHK' Normal use of VU/VU and CU/CD buttons (Este menu no puede ser ajustado)
SANSUNG
Nota:Para conocer el tipo de chasis que es el televisor,este tendremos que comprobarlo,mirando el chasispor debajo,y lo tenemos junto al Flyback
-con el tvc desconectado,presionamos las teclas en el mando a distancia de Mute182 y Power,el televisor seconectaa en el Service mode y en la pantalla son saldra GAMMA GAIN 1,usar los botones de Mute y Menupara mover los valores arriba y abajo,y los de volumen+ y volumen - para realizar los cambios paramemorizar presionar la tecla ADD y no la incorpora el TVC presione power.
-Con el televisor en Stand-By presionar en el mando a distancia las teclas MUTE 1 8 2 POWER y saldra enpantalla el menu de fabrica.
-Con el TV en stand-by pulsar las teclas siguientes con el mando a distancia: Display,Menu,Mute y Power.Con CH +/- se selecciona el valor a ajustar,y con VOL+/- se ajustan los valores.
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
4/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
-Con el TV en Stand-By pulsar la tecla Display----,p.std----mute----power este modo es para los chasis S15
SHARP
-En la parte trasera del tvc,los modelos que llevan como una especie de conector con pines,hay que puentearlos pines 3 y 6,despues de este debemos pulsar en el mando a distancia mode,y ajustar los valores quequeramos con el mas y menos.
-Desconectar el TV de la red,con las teclas CANAL+ y VOL+,pulsadas simultaneamente conecte el TV.Paraseleccionar los valores a ajustar Canal + y -.para ajustar con volumen + y -,y para memorizar pulsar Power ydespues desconectar el tvc de la red
MODO DE SERVICIO PARA LA SERIE G.1 - Antes de todo,ahi que realizar un Reset con el mando a distanciapara que los ajustes esten en modo normal.
2 - Destapar el TV, y puentear las puntas de prueba TP2001 y TP2002, que estan al lado del IC2001. Paraentrar en el Modo de Servicio.
3 - Una vez en Modo de Servicio, pulse Canal arriba o abajo con el mando a distancia o tvc.Saldra enpantalla una "S" con un número que varia de 0 a 33. Así puede seleccionar el Item que quiera ajustar.
4 - Seleccionado el Item, con Volume arriba o abajo aparece "D" con un número en la esquina inferiorderecha. - Para salir quitar el cortocircuito de TP2001 y TP2002.
Estos ajustes es necesario hacerlos cuando se sustituye los IC201, IC 2001, IC2002, IC3001 y el trc.
Cuando se sustituya e circuito integrado IC201 utilize el Item: S26 (MTS).Si reemplaza el IC 2002 losvalores iniciales están en el IC2001.Cuando se sustituye el IC2001 los datos estan en el IC2002.Los valoresS17, S19 y S22, su valor normal es: 0.El valor S5 debe fijarse en: 3.El valor S24 debe fijarse en: 32.
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Modo de servicio para Sharp 37Et-35S
Presionar simultaneamente,las teclas de volumen menos (V-) y programa mas (P+)
SANYO
Presionar a la vez las tecla de memoria del mando a distancia,y la memoria(M)que se encuentra en el panelfrontal de tvc.
Con el mando a distancia mantener presionada la tecla Menu del mando y pulsar el pulsador numero 2 delmando a distancia
Encender el TV. Pulsar la tecla Memoria del panel frontal de televisor aproximadamente 3 segundos.Seguidamente pulsar la tecla M del mando a distancia,y seguidamente la tecla Sonido(Sound),para ajustarcon la tecla mas/menos del volumen,con la tecla sound seleccionamos los ajustes que queramos realizar.
SONY
Con el televisor en Stand-by pulsar las teclas del mando a distancia la siguiente secuencia I+ despues elnumero 5 despues la tecla - (menos)de volumen y por ultimo la tecla pantalla,si hemos entrado en el modode servicio nos saldra en la pantalla TT.Sigue las indicaciones en pantalla pulsando las teclas Menu yvariando los parametros con las teclas roja y verde.Para salir del modo de servicio pulsar menu hasta quesalga de nuevo TT y pulsar posteriormente dos veces 00.
Estando el TV desconectado del interruptor, presione el botón de servicio que se esta en la parte de atras delTV, en el modulo de conectores. Mantener presionado mientras enciendes el TV con el mando a distancia.Con Audio y Video selecciona los menus. Con las teclas 1 y 4 elegir lo que queramos ajustar, y con lasteclas 3 y 6 ajustamos. Para memorizar los ajustes presionar Muting y despues Enter. Para salir del modo deservicio pulsar Power.
Estando el tvc en Stand-by, En el mando a distancia,presione las teclas (Display 5 Vol y Power on) o ( poweroff, Display,5 y power on). Con los teclas 1 y 4 elegimos los ajustes a realizarcon las teclas 3 y 6 ajustamoslos valores. Para memorizar los ajustes presione las teclas Muting y Enter,y para salir Power.
A continuacion una serie de codigos para probar si no logramos entrar con los 2anteriores: [PWR OFF] - [DISP], [5], [VOL+], [PWR ON] o [PWR OFF] - [DISP], [5], [PWR ON] o [PWR OFF] - [DISP],[5], [VOL+], [PICTURE], [PWR ON]
TOSHIBA
Mientras presionas el interruptor general de encendido presionas a la vez mute en el mando a distancia.denuevo presiona otra vez mute pero manteniendo mas tiempo pulsada la tecla,mientras presionas mutepresionas tambien TV en el frontal del televisor,despues suelta mute,entonces te saldra una S en la partesuperior derecha en pantalla.Entonces presionas Menu y ya estas en modo de servicio,con channel up yDown seleccionas el ajuste a cambiar,y con volumen up/down cambias los valores.
Estando el televisor conectado presionar dos veces Mute en el mando a distancia,en la segunda pulsacion
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
5/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
debe de mantenerse presionada la tecla Menu,mientras simultaneamente presiona mute en el panel frontaldel TVC,cuando nos aparezca S en la pantalla,otra vez pulsaremos Mute,con la tecla deprograma,seleccionamos la funciona a ajustar,y con las teclas de volumen ajustamos los valores,
THOMSON
Estando el televisor conectado y funcionando,por el televisor en Stand-by con el mando adistancia,seguidamente apagas el televisor con el interruptor principal,ahora pulsas la tecla Azul del mando adistancia y conectas el interruptor pricipal hasta que te salga Setup,y ya estas en el modo se servicio deThonson,ahora ten cuidado con la modificacion de valores,y realiza los ajustes con sumo cuidado.
Modos de Servicios extraidos de Internet
Marca Modelo/Chasis Modos deServ icio y deHotel
Repair Adv ice
NOKIA Compact B-E2
Digital chassis
Service Mode First Method - set with CCU11 uPC: press buttons from remote controls
"mon-stereo" - "C" - "hypersonic" whithin 1 sec. Tha display shows
"SE".
NOKIA Compact B-E2
Digital chassis
Service Mode First Method - set with CCU12 uPC: press the contact behind the small
borehall on set front pannel (controls) and then button "S" whithin 5
sec. Tha display shows "SE".
PHILIPS TV/VCR chassis Hotel Mode Activation
Select program 38, press "SELECT" on local keyboard and
"SLEEPTIMER" on remote control for at least 4 sec.. At activation the
"H+" is displayed. To remove this display turn off-on the TV set.
De-Activation Select program 38, then press "SELECT" on local
keyboard and "SLEEPTIMER" on remote control for at least 4 sec..
When de-activation is OK, a "H-" is displayed. To remove this display
turn off-on the TV set.
PHILIPS ANUBIS A
chassis
2 local controls
Hotel Mode First Method
Activation
Select program 38, press "SELECT" on local keyboard and
"SLEEPTIMER" (or
"OSD") on remote control for at least 4 sec.. At activation the "H+" is
displayed. To remove this display turn off-on the TV set. De-Activation
Select program 38, then press "SELECT" on local keyboard and
"SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When
de- activation is OK, a "H-" is displayed. To remove this display turn
off-on the TV
set.'
PHILIPS ANUBIS A
chassis
2 local controls
Hotel Mode Third Method
Activation
Select program 38, then press "INSTALL" on local keyboard and
"SLEEPTIMER" on remote control for at least 4 sec. When activated
"HOTEL
MODE" a green "H" is displayed. To remove this display turn off-on the
TV set.
De-activation Select program 38, then press "INSTALL" on local
keyboard and "SLEEPTIMER" on remote control for at least 4 sec.
When de-activation is OK, a green "H" is displayed. To remove this
display , turn off-on the TV set.
PHILIPS ANUBIS A
chassis
8 local controls
Hotel Mode First Method
Activation
Select program 38, press "SELECT" on local keyboard and
"SLEEPTIMER" (or
"OSD") on remote control for at least 4 sec.. At activation the "H+" is
displayed. To remove this display turn off-on the TV set. De-Activation
Select program 38, then press "SELECT" on local keyboard and
"SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When
de- activation is OK, a "H-" is displayed. To remove this display turn
off-on the TV
set.'
PHILIPS ANUBIS A
chassis
8 local controls
Hotel Mode Second Method
Activation
Select program 38, then press simultaneously "INSTALL" and
"PROGRAM+"
on local keyboard.
De-Activation Select program 38, then press simultaneously "INSTALL"
and "CONTROL" on
local keyboard.
PHILIPS ANUBIS A
chassis
8 local controls
Hotel Mode Third Method
Activation
Select program 38, then press "INSTALL" on local keyboard and
"SLEEPTIMER" on remote control for at least 4 sec. When activated
"HOTEL
MODE" a green "H" is displayed. To remove this display turn off-on the
TV set.
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
6/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
De-activation Select program 38, then press "INSTALL" on local
keyboard and "SLEEPTIMER" on remote control for at least 4 sec.
When de-activation is OK,
a green "H" is displayed. To remove this display , turn off-on the TV
set.
PHILIPS G8 chassis Hotel Mode Activation
Select "Video2" mode. Press the remote control control keys
"TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel
Menu "HOTEL
MODE" must be set "ON"
De-activation Select "Video2" mode. Press the remote control control
keys "TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel
Menu "HOTEL
MODE" must be set "OFF"
PHILIPS G8.1ECO
chassis
Hotel Mode Activation
Select "Video2" mode. Press the remote control control keys
"TELETEXT" and "FEATURE" in sequence within 1 sec. In the
displayed Hotel Menu "HOTEL MODE" must be set "ON"
De-activation Select "Video2" mode. Press the remote control control
keys "TELETEXT" and "FEATURE" in sequence within 1 sec. In the
displayed Hotel Menu "HOTEL MODE" must be set "OFF"
PHILIPS AA5 chassis Hotel Mode HOTEL MODE
Activation
Select program 38, press "MENU" on local keyboard and
"SLEEPTIMER" (or
"OSD") on remote control for at least 4 sec.. At activation the "H+" is
displayed. To remove this display turn off -on the TV set.
De-Activation
Select program 38, then press "MENU" on local keyboard and
"SLEEPTIMER"
(or "OSD") on remote control for at least 4 sec.. When de-activation is
OK, a
"H-" is displayed. To remove this display turn off -on the TV set.
PHILIPS G8.1 chassis Hotel Mode Activation
Select "Video2" mode. Press the remote control control keys
"TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel
Menu "HOTEL
MODE" must be set "ON"
De-activation Select "Video2" mode. Press the remote control control
keys "TELETEXT"
and "FEATURE" in sequence within 1 sec. In the displayed Hotel
Menu "HOTEL
MODE" must be set "OFF"
PHILIPS GR1-AX (8
buttons)
Hotel mode for
models with
uP
TMP47C434N-
R221
Select program 38 on the TV
Simultaneously press the STORE key on the TV and SLEEPTIMER on
the remote for 4 about seconds (toggles hotel mode)
Notes:
The maximum volume in hotel mode will be the volume present when
activating it
STORE or INSTALL mode can not be entered
The program number is displayed on the screen for 4 seconds
A green 'H' appears in the left bottom of the screen, which can be
removed by powering down the TV and powering it up again
PHILIPS ANUBIS A
chassis
2 local controls
Hotel Mode Second Method
Activation
Select program 38, then press simultaneously "INSTALL" and
"PROGRAM+"
on local keyboard. De- Activation Select program 38, then press
simultaneously "INSTALL" and "CONTROL" on
local keyboard.
PHILIPS L6.1 (without
Teletext)
Hotel mode Select program 38 on the TV
Simultaneously press the - key on the keyboard of the TV and the OSD
key of the remote control
PHILIPS GR2.X Service Mode Short circuit pins M33 and M34 before powering up the TV. When
powered up the TV LED will show as orange after which the short
circuit can be removed. SER will be displayed on screen. Now press
simultaneously keys INSTALL and PROG+ on the keyboard of the TV
to activate the service menu
PHILIPS GR1-AX (8
buttons)
Hotel mode for
models with
uP
TMP47C434N-
3414/3415, uP
TMP47C634N-
R494
Select program 38 on the TV
Simultaneously press the STORE key and the PROGRAM+ key on the
TV for 4 about seconds (hotel mode on)
Simultaneously press the STORE key and the CONTROL- key on the
TV for 4 about seconds (hotel mode off)
Notes:
The maximum volume in hotel mode will be the volume present when
activating it
STORE or INSTALL mode can not be entered
The program number is displayed on the screen for 4 seconds
ANUBIS B Service Mode Second method: With the TV powered off (disconnected from the
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
7/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
PHILIPS mains!) short circuit pins M61 and M62 (next to IC7600). Power up the
TV and remove the short circuit. A 'S' wil l be displayed indicating it is
in service mode
Simultaneously press the P- and VOL+ keys on the TV. The screen now
shows 'service menu'.
To allow hotel mode from being set on and off you have to select
Option 2 with the remote and set 'Hotel' to 'on'.
Exit the service mode by putting the TV into standby
PHILIPS ANUBIS B Service Mode First method: Select program 38 on the TV
Simultaneously press the P key and the VOLUME+ key
(keyboard/remote)
To enable hotel mode you should set 'HO' to 'one'
PHILIPS ANUBIS AA Service Mode Short circuit terminals M28 and M29 (IC7710)
PHILIPS A10E chassis Service Mode This model also supports the 062596 sequence followed by [i+]/[OSD].
Service default mode is entered using the 062596 sequence, followed
by the - button on the TV set itself.
Alternatively you can short-circuit pins 9261 and 9262 inside the set
and then powering it up
PHILIPS 20PV220 Service Mode TV preset 38
Push STOP -button on the remote and the PLAY -button on the TV
simultaneously, for 5 seconds
You´ll get the service menu on screen
Clear EEPROM is the only cure for the problem that all items in
installation menu are in ” non active ” mode with red text
Close TV from remote, and on again
Tune channels again
PHILIPS 21PT263A Service Mode Short circuit pin 1 of the EEPROM (24C08) to ground
PHILIPS ANUBIS Service Mode Short circuit terminals M31 and M32 (IC7710)
PHILIPS 20PT424A Service Mode Short circuit pin 1 of the EEPROM (24C08) to ground
SchaubLorentz
SL0014KO
CTV-VCR
Service Mode To enter SERVICE MODE, Unplug AC cord ti l l lost actual clock time.
Then press and hold Vol (-) button of main unit and remote control key
for more than 2 seconds. The both pressing of set key and remote
control key will not be possible if clock has been set. To reset clock,
either unplug AC cord and allow at least 30 minutes before Power On
or alternatively, discharge backup capacitor.
SCHNEIDER TV8 chassis Service Mode Service-Mode
Before being switched to the service mode the unit must be set to a
channel
with a test pattern. Note: The parameters are stored in changed.
Press the red key and the blue key on the remote control
simultaneously. Within 5 seconds, press the key P-and the key V+ on
the local control panel simultaneously
The title SERVICE Vxxx (xxx is for software version), appears in the
screen.
Keys P+ and P- (program) Call up tuning parameters
Keys V+ and V- (volume) Modify tuning parameters
Display Operation
VP Adjust the vertical swift.
HP Adjust the horizontal swift.
VP Adjust the vertical picture height. Is the setting range not sufficient
the range must change with the point CRT.
VL Adjust top and button vertical l inearity of screen centre.
VB Adjust the intensity of the EHT. VB=24
PA Make vertical l ines parallel with screen edge.
HA Adjust the horizontal size.
CC Adjust vertical l ines in corners. Basic setting is 0. Setting should
only
be changed if PA balance cannot be adjusted satisfactorliy.
PT Adjust values so that picture has same with at top and bottom
edges or
other vertical l ines are parallel with each other.
R Colour drive adjustment
G Colour drive adjustment
B Colour drive adjustment
S-ADJ Connected a Test-picture with stereo signal to the tuner and
adjust
the TV. Connected Oscilloscope to Pin of ST601. Adjust to lowest
crostalk
between the channels.
L-ADJ Connect Oscil loscope to Pin 1 of ST601. Connect a Test-picture
(antenna level>60dBuV/75Ohm) with stereo signal (27kHz
frequenceshift.54%
modulation factor) to the tuner and adjust the TV.
CRT Gear to vertical deflection. In dependence of the picture tube 0 or
1.
GR/G+GL Shows like the Cutoff registration locks of in place. Its
useable
to adjust G2-adjustment.
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
8/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
DELAY Superimpose the luma signal on the chrominance signal.
Sharp 51DT25H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote
control.
Sharp 4BS-C Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp 51AT15H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode - 'SERV' appears on
the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
Sharp 51CS05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 51DS02H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 51DS05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 59CS03H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
9/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
Turn the set off at the mains to exit the service mode.
Sharp 37AT25H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode - 'SERV' appears on
the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
Sharp 51DS03H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 4BS-B Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode and SERVICE
SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 4BSA Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of
connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel
up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.
Sharp 37ET35H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote
control.
Sharp 37EM33H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote
control.
Sharp 37DT25H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
10/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote
control.
Sharp 37AT25H Cancel child
lock
1 with tv switched off hold in both vol -- and prog + on tv 2 switch on tv
it is now in service mode 3 use channel + to scroll through menu and
stop at n v m (non volati le memory)
4 there will also be a 2 digit number in red on the screen as well as
another 2 digit number in green, using the vol + button and at the
same time observe the green display change the green number until
C5 appears 5 At this point the red display shold show 00 for lock to be
of
if it shows 01 change to 00 using 0 button 6 switch off the set
ps the menu is available for many adjustments take care !!!
Sharp 66CS05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 37AM23H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode - 'SERV' appears on
the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
Sharp 37AM23H Child Lock
removal - pin
no not known
PRESS VOL - ON TV & CHILD LOCK ON REMOTE TOGETHER ,
PRESS MODE ON REM, USING CHANNEL +/- TO SELECT CHILD
LOCK , SELECT NEW PIN PRESS MODE E
Sharp 37AM12H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode - 'SERV' appears on
the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
Sharp 59CS05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 37DM23H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
To exit the service mode, press the standby button on the remote
control.
Sharp DV5135H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and
6 (Service) of connector of CN1 on the Video
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
11/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
unit. Note that the wire is used just l ike a passing contact switch
5. 'SHARP Software Service Ver' wil l appear on the screen Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp 59CSD8H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DV6640H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp 66AS06H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV6635H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV66083H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode
Sharp DV6603H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode
Sharp DV5105H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and
6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just l ike a passing contact switch
5. 'SHARP Software Service Ver' wil l appear on the screen Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV5107H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and
6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just l ike a passing contact switch
5. 'SHARP Software Service Ver' wil l appear on the screen Use the
channel up and down buttons to move between the options
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
12/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV5940H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV5131H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot
on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DV3751H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot
on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DV5150H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot
on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DV5161H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of
connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel
up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.
Sharp DV5165H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode and SERVICE
SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DV5180H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode and SERVICE
SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
13/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
Sharp DV5903H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode
Sharp DV59083H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode
Sharp DV5932H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV5935H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV5937H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp DV51083H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode
Sharp 66ES05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 59DS03H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 59DS05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
14/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 59ES03H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 59ES05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 59ESD7H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 5BSA Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode - 'SERV' appears on
the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
The data is stored automatically at switch off
Sharp 66AS05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp 66CS03H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 66DS03H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
15/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 66DW18H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DV3760H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of
connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel
up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.
Sharp 66ESD7H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp 76DW18H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp BCTVA Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 (GND) and 6 (Service) of
the service slot on the Video Unit
4. SERVICE SOFTWARE will appear on the screen
5. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp D3000 Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the service switch again to exit the service mode
Sharp CW100 Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DECO-4
Chassis
Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
16/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and
6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just l ike a passing contact switch
5. 'SHARP Software Service Ver' wil l appear on the screen Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp Deco-5 Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and
6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just l ike a passing contact switch
5. 'SHARP Software Service Ver' wil l appear on the screen Use the
channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the receiver off at the mains to exit the service mode
Sharp S3B Chassis Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 2 and 6 of the service slot
on the video PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire Use the channel up and down buttons to
move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp DV3770H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of
connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire To select an adjustment use the channel
up and down buttons
To change the data press the data buttons
The changes are stored automatically
Turn the set off at the mains to exit the service mode.
Sharp 66DS05H Service Mode 1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the
receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it wil l be in service mode
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
SIEMENS FM550.XX
chassis
Emergency
Data
The processor IC850 in this TV receiver is fitted with two memories in
which the picture
geometry data are stored. If this IC fails or the data have been
changed, the TV receiver must be switched on the emergency data set.
Emergency Data Loading the Emergency Data :Press and hold the "P-
"button on the local keyboard and switch the TV on with the mains
button. In doing so, the data sets for the picture geometry values, the
deflection and chrominance data are loaded from the keyboard control
unit into the respective modules. Subsequently, call up the Info Center
Menu - Special Functions - Service - Code Number 8500 - Geometry
and change the
setting if requested. To store the data Call up "end without mem." and
select "End with
mem." using the buttons < or >. Initialisiation of the uP (IC8500) (eg.
After changing the uP IC 850) - Connect Pin 1 of the processor to
chassis and switch the TV on with the mains switch to load the
EEPROM in the processor IC850
SONY KV27S45 ID CODES
after replace
EEPROM On
remote control
"Press"
DISPLAY "5" -
"VOLUME +" -
"POWER"
To WRITE TO
EEPROM
"Press" -
"MUTING" -
"ENTER"
To INITIALIZE
ID-0 153, ID-1 27, ID-2 13, ID-3 195, ID-4 31, ID-5 1, ID-6 1, ID-7 64
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
17/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
EEPROM
"Press" "8" -
"ENTER"
SONY KV32S25 ID CODES
after replace
EEPROM On
remote control
"Press"
DISPLAY "5" -
"VOLUME +" -
"POWER"
To WRITE TO
EEPROM
"Press" -
"MUTING" -
"ENTER"
To INITIALIZE
EEPROM
"Press" "8" -
"ENTER"
ID-0 25, ID-1 21, ID-2 31, ID-3 0, ID-4 27, ID-5 0, ID-6 1, ID-7 0
SONY KV32XBR85 ID CODES
after replace
EEPROM On
remote control
"Press"
DISPLAY "5" -
"VOLUME +" -
"POWER"
To WRITE TO
EEPROM
"Press" -
"MUTING" -
"ENTER"
To INITIALIZE
EEPROM
"Press" "8" -
"ENTER"
ID-0 120, ID-1 127, ID-2 126, ID-3 52, ID-4 28, ID-5 NA, ID-6 NA, ID-7
NA
SONY KV32V16 ID CODES
after replace
EEPROM On
remote control
"Press"
DISPLAY "5" -
"VOLUME +" -
"POWER"
To WRITE TO
EEPROM
"Press" -
"MUTING" -
"ENTER"
To INITIALIZE
EEPROM
"Press" "8" -
"ENTER"
ID-0 120, ID-1 127, ID-2 72, ID-3 36, ID-4 19, ID-5 NA, ID-6 NA, ID-7 NA
SONY KV32V65 ID CODES
after replace
EEPROM On
remote control
"Press"
DISPLAY "5" -
"VOLUME +" -
"POWER"
To WRITE TO
EEPROM
"Press" -
"MUTING" -
"ENTER"
To INITIALIZE
EEPROM
"Press" "8" -
"ENTER"
ID-0 89, ID-1 55, ID-2 175, ID-3 10, ID-4 27, ID-5 141, ID-6 6, ID-7 0
VESTEL 11AK20S
CHASSIS
Service Mode How to enter and exit the SERVICE Menu:
Enter the Main Menu
Press the digits 4, 7, 2, and 5, respectively
Press MENU key to exit
There're two selections in the Service Menu: "ADJUST…" and
"OPTIONS…" ADJUST Menu: Move the selection bar on the item
"ADJUST…" using the P+ or P- keys,
Select the item "ADJUST…" using the < or > keys,
The items below will be displayed (one of them at one time),
1) AGC (Automatic Gain Control) 8) HSH (Horizontal Shift)
2) VA1 (Vertical Amplitude for 4:3, 50Hz) 9) WG (White Point GREEN)
3) VA2 (Vertical Amplitude for 16:9, 50Hz) 10) WR (White Point RED)
4) VA3 (Vertical Amplitude for 4:3, 60Hz) 11) WB (White Point BLUE)
22/ 12/ 12 m M odos de ser vicios de Television por Valet r onik
18/ 18f ile: / / / D: / aver ias/ t v/ M odos de Ser vicio de TV_ar chivos/ m odosdeser vicios. ht m
5) VA4 (Vertical Amplitude for 16:9, 60Hz) 12) CR (Cut-off Red)
6) VSH (Vertical Shift) 13) CG (Cut-off Green)
7) VL (Vertical Linearity) 14) OSH (OSD Horizontal Position)