Post on 04-Jun-2018
8/13/2019 Tubo t8 120 Vultima2
1/7
D+LED
8/13/2019 Tubo t8 120 Vultima2
2/7
D+LEDLEDTubeFeaturesSpecial design of end-cap
Design of removable end-cap provides quick replacement of inner-transformer by pressingthe switch on the end caps easily. Different from other tubes which fixing end-cap by glue, this
new tube designed by our R&D, and it enables customers open the tube to replace
inner-transformer if the transformer fails after some years usage.
Perfect design to avoid led failure in series
Our company invested much in R&D and researched a new technology to make all leds in the
tube work independently. Namely, if one led fails, no impact to other led. However, most led
tube in the market designed with at least 7 leds per series. 1 led doesnt work, all other 6leds
or more not work. Lumen of the whole tube will drop much.
Top quality PC cover
For our tube, both transparent and milky covers are available. For milky cover, when lighten
the tube, LEDS are invisible. Namely, light effect is very even and same as traditional
fluorescent light. We realized 100% perfect replacement.
Great Lighting source
The chip of led is of high quality and bigger size, 10*23 chip, which is from Epistar in Taiwan.
It can resist higher anti-static and distribute more brightness, esp. 3528 SMD LED is at least
2000mcd or 6.5lm-7lm.
Low light attenuation
esp. the white light is adopting new technology, less than 3% in 1000h, however, the
traditional attenuation of white color at least 30%;
Ultra quality inner transformer
We have our own researching and development team to focus on LED driver. The driver we
researched for our tube is Isolate high. PF. Driver and UL approved.
More durable & robust
It can light up to 10 years, comes with 3 years guarantee time.
High safety performance
We have double isolation from our transformer. What is more, our tubes are UL(E344776),
CE, certified and RoHS compliant. With the range of CE, we have passed through EMC and
LVD test, so you can apply the tube for your projects freely.
Tube package
High quality cylindrical package and pin protection avoids shipping damage. Please refermore information on last page about package information.
8/13/2019 Tubo t8 120 Vultima2
3/7
D+LED
Drawing
Notes:
1. All dimension units are millimeters.
2. All dimension tolerance is 1mm unless otherwise noted.
ApplicationWidespread use in Family, School, Office, Showing Room, Meeting Room
Commercial Building, Tower, Hotel, Restaurant Factory, Production Line, Warehouse
Pathway lighting, Street lighting Subway station, bus and train
8/13/2019 Tubo t8 120 Vultima2
4/7
D+LEDIlluminance
T8-N8W-60/120/150(cool white) T8-N8WW-60/120/150(warm white)
CharacteristicsAbsolute Maximum Rating at TA=25
Parameter Symbol Absolute Maximum RatingT8-N8W-60/120/150 Unit
Working Voltage V AC85-265V V
Power Dissipation PD 8 / 12 / 16 / 18 W
Electrostatic discharge ESD 800 V
Operating Temperature Topr -20+50
Storage Temperature Tstg -3 0 +60
Electrical / Optical Characteristics at TA=25
Length Part No. Color Color Temp. Lumen Power CRI(Typical) Viewing Angle
60cm T01/T8-N8NW-60 Natural white 4000-4500K 840 lm 8W 78 120
120cm T04/T8-N8NW-120 Natural white 4000-4500K 1680 lm 16W 78 120
150cm T06/T8-N8W-150 Cool white 5000-6000K 1875 lm 18W 78 120
Notes: Tolerance of measurement of luminous intensity15%.
8/13/2019 Tubo t8 120 Vultima2
5/7
D+LEDInstallationInformationPrecaution: Switch off power before doing any works.Installation for double-ended power tube
Method A
If lighting fixtures wire connection is inductor ballast, installation as bellow.
Step 1. Remove the traditional fluorescent tube from the lighting fixture.
Step 2. Take out the inductor ballast from the lighting fixture.
Step 3. After take out the ballast, there will have two wires. One wire connects to right side
and another wire connects to left side.
Step 4. Install LED fluorescent tube light into lighting fixture.
Before change connection After change connection
Method B
If lighting fixtures wire connection is Electronic ballast, installation as bellow.
Step 1. Remove the traditional fluorescent tube from the lighting fixture.
Step 2. Take out the starter and electronic ballast from the lighting fixture.
Step 3. After take out the ballast, there will have two wires. One wire connects to right side
and another wire connect to left side.
Step 4. Install Torshare Led tube light into lighting fixture.
Before change connection After change connection
8/13/2019 Tubo t8 120 Vultima2
6/7
D+LEDInstallation for single-ended power tube
Step 1, Remove the fluorescent lamp.
Step 2, Cut off all wires which connected to inductive ballast or electrical ballast.
Step 3, Connected two wires from the lamp holder. (The additional wire connector and No. 18
AWG wiring maybe required)
Step 4, Connected the two wires to branch circuit L and N.
Step 5, Install LED tube.
Step 6Switch on power.
8/13/2019 Tubo t8 120 Vultima2
7/7
D+LEDWarning LED Fluorescent tube and all of its components must not be subjected to mechanical
stress.
The complete installation must be done by an electrical expert who is familiar with the valid
directives.
If any doubt about the installation or use of this product, consult a competent electrician
Don't use it if aluminium of the tube have any damage or distortion. Otherwise, the product
or the installation might not be sufficiently safe!
Switch off power of the mains supply or respectively of the connection lead before doing any
works.
Assembly must not damage or destroy conducting paths.
Make sure that the product is mounted on a stable, even and tilt-fixed background.
Keep away from direct sunshine and high temperature
Indoor use only
PackingInformationLength
Outer Carton Size
(LWHcm
Qty/Carton
pcs
N.W
(kg)
G.W
(kg)
60cm 66*21*29.5 30 8 11
120cm 126.5*21*28 30 13 19
150cm 157*21*28 30 18 24