BTS Presentation Alcatel

5/26/2018 BTS Presentation Alcatel

1/54

12/29/2010 Turnotech Solutions


2/54

Switch OFF the

BTS cabinet and

disconnect Abis

connectors from

DDF before offline

start



3/54

Disconnect

the Abis

connector

from The DDF



4/54

Switch ON the

BTS cabinet

breakers and

connect the

Laptop with

BTS



5/54

User Name

COMMTE

PasswordCOMMTE



6/54

CommunicationPort setting



7/54

Afterconnecting

this windowwill be appear



8/54

Go to

Configuration->

BTS-SWDownload->

to download

BTS software



9/54

After BTS-SW

downloadthis window

will appear



10/54

Go to offlineFiles and select

First File ofMaster File.



11/54

Go to offlineFiles and

select FirstFile of DDL

file.



12/54

Click ok tostart

downloadingSW



13/54

BTS softwarestarts to

download.



14/54

All theseFiles are

downloaded



15/54

Go to

ConfigurationBTS

commissioning



16/54

Click startcommissioning



17/54

Edit QmuxAddress



18/54

Edit sectorMapping



19/54

Check AllTwin TREs.



20/54

Click EndCommissioning

Click


21/54

All modulesShifted to

updatemodules.



22/54

Click No to

end



23/54

Reconnect the

Abis connector at

DDF by verifying

the TX/RX cables

properly



24/54

Give Hard Reset to

BTS cabinet as the

OML has established

to put the site on

Downloading.



25/54

OFF Line Commissioning

Completed

Successfully.



26/54

Go toconfiguration>>

Hardware

setting>>BeginHW modification



27/54

Go to

configuration>BTS

commissioning

Go to startcommissioning>Edit Q1 Address,

Edit SectorMapping and Twin

TRA setting as in

offline.12/29/2010 Turnotech Solutions


28/54

Go toconfiguration>

Hardwaresetting>EndModification to

end onlinecommissioning



29/54

Connect the Abis connector at DDF by verifyingTx/Rx cable properly.

OML will be established after primary Abis hasconnected to DDF.

Give hard reset to BTS after OML has established.

Put site on Downloading from OMC.

O&M will be established as downloading completes.

Connect Laptop to BTS MMI port. Go to configuration>Hardware setting>Begin

Hardware modification.



30/54

Go to configuration>BTS commissioning>startcommissioning.

Edit Qmux Address Edit sector mapping

Check all Twin TRA setting. Click end commissioning and shift all modules from

selected modules to available modules. Go to configuration>Hardware setting>End Hardware

modification.

Click yes when an automatically hardwaremodification window appears. Hw Audit will be run and all Hardware will be shown

after sometime.



31/54

ON Line Commissioning

Completed

Successfully.



32/54

combiner Fan Unit

Tres

clockAlarmcard

HardwareShown in

softwarewindow



33/54

Alarmswindow



34/54

Transceivers

Shown inwindow



35/54

Four type of Transceivers in Alcatel Equipment

TRAGE>Gsm Single TRE

TRADE>Dcs single TRE

TGT09>Gsm Twin TRE TGT18>DCS Twin TRE

TAGHE>High power TRE



36/54

VSWR

Shown inwindow



37/54

SectorsShown

In window



38/54

Station units



39/54

BSC SBLs(security block levels)BTS OM & Sectors.Sec

RSLs can be unlock

from local Terminal.



40/54

If a TRE or combiner is in Not Operational or FOS statethen disable it then initialize it by using init command.

If TRE or combiner can not operational by doing abovecommand then remove it by using the following method.

Go to configuration>>Hardware setting>>Begin HW

modification. Go to Configuration>>Hardware setting>>Remove. Remove the Hardware from BTS. Window will be appear of Hardware removal, select the module

to remove. Go to Configuration>>Hardware setting>>End Modification. Click yes when configuration changes window appears.



41/54

HardwareRemovalMethodStep:1



42/54

HardwareRemoval

Step:2



43/54

HardwareRemoval

Step:3



44/54

When a module goes in FOS state then it must be disableby using disable command before initializing it by usinginit command otherwise it will not goes to operationalstate.

When a module is in Not Operational state with color

white then it means it has not got its RSL number still.Reload BTS data by going to configuration>Reload Btsdata or using a method of Begin Hardware then EndHardware as discussed earlier. It will take some time tobecome operational.

When a module is in MSD or MSA state then it will not

get any command because its maintenance has seized for awhile. When TRE RSL has locked then then its RSL will not be

stable, so unlock the TRE from OMC.



45/54

Sometime there is some faulty hardware in Bts thats whyother sectors or TREs can effect and can not work properly.Due to these faulty hardware other sectors or TREs can bedown so simply remove this hardware. By this methodother hardware become in operational state.

Some time SUMA can not work properly thats whywhole Bts effects so change the slot of SUMA and givehard reset to Bts.

If modules in a shelf can not powers up then check itspower cable at the back ports of Bts or check it RI cable.

Also check the power switch for the concern shelf. If a EACB card is Not operational or FIT state then

initialize it from software. If it again goes in FIT state thenAlarm card is faulty.



46/54

Some time Primary Abis is stable by showing LED on Sumacard but OML can not become stable, It means that AbisLED is fake. So check the Tx/Rx cable from both Bts endand microwave end and make sure that it is correctlyconnected. Also check Tx/Rx patching on DDF by usingLED. Make sure that LED blinks on every pair on DDF. Alsocheck the BNC and Abis connectors. Abis cable which isconnected from Suma card to Bts board can be faulty so alsoverify it.

If a TRE or combiner can not operational than change its slotthen verify it.

Vswr issues can be resolved by checking connectors fromBts end and feeder end. The last option for Alcatel equipment to become operational

is the Hard reset of Bts.



47/54



48/54

A

AN Antenna Network

BBCB BTS Control BusBSII Base Station Controller

BSS Base Station SubsystemBTS Base Station TransceiverBTSW BTS-Terminal for Windows

CCCF Cabinet Cooling FanCDM Configuration Data Message

CLEI Common Language EquipmentCLLK Clock LinkCPF Configuration Parameter FileCRC Cyclic Redundancy CheckCU Carrier Unit



49/54

DDC Direct CurrentDMA Deferred Maintenance Alarm

EEQU Equipped

FFIA Format Identifier for Application part of RI

FIM Format Identifier ManufacturingFIT Faulty In TrafficFLT FaultyFOS Faulty Out of ServiceICS Item Change StatusIT In Traffic

L

LDA Local Defence ActionLRA Local Recovery Action

MMI Maintenance InformationMSA MSD AutoMSD Maintenance Seized



50/54

N

NEQ Not Equipped

NOP Not Operational

O

O&M Operation and Maintenance

OMU Operation and Maintenance Unit

OMUA OMU A RITOMUB OMU B RIT

OP Operational

OPR Operator

P

PADD Physical Address

PMA Prompt Maintenance



51/54

R

RA Radio Access

RF Radio Frequency

RFH Radio Frequency Hopping ( also known as : Synthesizer Hopping )

RI Remote Inventory

RIT Replaceable Item

RX Receiver or receive .....

RTC Remote Tunable Combiner

S

SBL Security Block Level

SCFE Station Unit Control Function Entity RIT

SOS System Out of Service

SUM Station Unit Module

SUMP SUM PCM RIT

SW Software



52/54

SSBL Security Block LevelSCFE Station Unit Control Function Entity RITSOS System Out of ServiceSUM Station Unit Module

SUMP SUM PCM RITSW SoftwareT

TLV Tag, Length, ValueTRE Transceiver Module (combined Transmitter / Receiver

functionality for base band and RF signals)

TS TimeslotTX Transmitter or transmit .

VVPMA Very Prompt Maintenance AlarmVSWR Voltage Standing Wave Ratio



53/54

W

WBC Wide Band Combiner

WTC Wait Traffic Clear

X

XBCB External BCB

XCLK External ClockXIOB External Input Output Board



54/54

BTS Presentation Alcatel

Documents

Transcript of BTS Presentation Alcatel